Ask question

Ask question

All categories

3 years ago

6

at stop light the truck traviling at 15m/s passes the carb as it starts from rest the truck travels at a constant relatively ,th

e car accelrate 3m/s^2, how much time does car take to the truck?.

1 answer:

Kaylis [27]3 years ago

7 0

What's the velocity?

You might be interested in

A police radar gun uses X-band microwave radiation at a frequency of 12.2 GHz. Microwaves travel at the speed of light, or 3x108

quester [9]

Answer:

A police radar gun uses X-band microwave radiation at a frequency of 13.1 GHz. Microwaves travel at the speed of light, or 3x108 m/s. Since the frequency shift will be small for practical car speeds and difficult to detect, the shifted frequency is compared to the original frequency, and the resulting beat frequency is used to determine the speed of the car.

a.) If Michael is traveling at 29 m/s, what is the resulting beat frequency that the radar gun detects?

ANSWER: 2533 Hz

Explanation:

6 0

3 years ago

if a stone is projected at an angle of 50 degrees to the horizontal with an initial velocity of 50m/s, what is the vertical comp

Vilka [71]

Answer:

38.3 m/s

Explanation:

To find vertical component of initial velocity, you'd have to use sine ratio:

$\displaystyle{\sin \theta = \dfrac{u_y}{u}}$

$\displaystyle{u_y}$ is vertical component of initial velocity and $\displaystyle{u}$ is initial velocity given which is 50 m/s.

A stone is projected at an angle of 50 degrees so $\displaystyle{\theta}$ = 50°. Substitute in the formula:

$\displaystyle{\sin 50^{\circ} = \dfrac{u_y}{50}}\\\\\displaystyle{50 \sin 50^{\circ} = u_y}\\\\\displaystyle{u_y = 38.3 \ \, \sf{m/s}}$

Therefore, the vertical component of initial velocity is approximately 38.3 m/s

(The picture is also attached for visual reference!)

3 0

2 years ago

What is the force per unit area at this point acting normal to the surface with unit nor- Side View √√ mal vector n = (1/ 2)ex +

Mumz [18]

Complete Question:

Given $\sigma = \left[\begin{array}{ccc}10&12&13\\12&11&15\\13&15&20\end{array}\right]$ at a point. What is the force per unit area at this point acting normal to the surface with $\b n = (1/ \sqrt{2} ) \b e_x + (1/ \sqrt{2}) \b e_z$ ? Are there any shear stresses acting on this surface?

Answer:

Force per unit area, $\sigma_n = 28 MPa$

There are shear stresses acting on the surface since $\tau \neq 0$

Explanation:

$\sigma = \left[\begin{array}{ccc}10&12&13\\12&11&15\\13&15&20\end{array}\right]$

equation of the normal, $\b n = (1/ \sqrt{2} ) \b e_x + (1/ \sqrt{2}) \b e_z$

$\b n = \left[\begin{array}{ccc}\frac{1}{\sqrt{2} }\\0\\\frac{1}{\sqrt{2} }\end{array}\right]$

Traction vector on n, $T_n = \sigma \b n$

$T_n = \left[\begin{array}{ccc}10&12&13\\12&11&15\\13&15&20\end{array}\right] \left[\begin{array}{ccc}\frac{1}{\sqrt{2} }\\0\\\frac{1}{\sqrt{2} }\end{array}\right]$

$T_n = \left[\begin{array}{ccc}\frac{23}{\sqrt{2} }\\0\\\frac{27}{\sqrt{33} }\end{array}\right]$

$T_n = \frac{23}{\sqrt{2} } \b e_x + \frac{27}{\sqrt{2} } \b e_y + \frac{33}{\sqrt{2} } \b e_z$

To get the Force per unit area acting normal to the surface, find the dot product of the traction vector and the normal.

$\sigma_n = T_n . \b n$

$\sigma \b n = (\frac{23}{\sqrt{2} } \b e_x + \frac{27}{\sqrt{2} } \b e_y + \frac{33}{\sqrt{2} } \b e_z) . ((1/ \sqrt{2} ) \b e_x + 0 \b e_y +(1/ \sqrt{2}) \b e_z)\\\\\sigma \b n = 28 MPa$

If the shear stress, $\tau$ , is calculated and it is not equal to zero, this means there are shear stresses.

$\tau = T_n - \sigma_n \b n$

$\tau = [\frac{23}{\sqrt{2} } \b e_x + \frac{27}{\sqrt{2} } \b e_y + \frac{33}{\sqrt{2} } \b e_z] - 28( (1/ \sqrt{2} ) \b e_x + (1/ \sqrt{2}) \b e_z)\\\\\tau = [\frac{23}{\sqrt{2} } \b e_x + \frac{27}{\sqrt{2} } \b e_y + \frac{33}{\sqrt{2} } \b e_z] - [ (28/ \sqrt{2} ) \b e_x + (28/ \sqrt{2}) \b e_z]\\\\\tau = \frac{-5}{\sqrt{2} } \b e_x + \frac{27}{\sqrt{2} } \b e_y + \frac{5}{\sqrt{2} } \b e_z$

$\tau = \sqrt{(-5/\sqrt{2})^2 + (27/\sqrt{2})^2 + (5/\sqrt{2})^2} \\\\ \tau = 19.74 MPa$

Since $\tau \neq 0$ , there are shear stresses acting on the surface.

3 0

3 years ago

Calculate the energy of a photon emitted when an electron in a hydrogen atom undergoes a transition from =7 to =1.

Harrizon [31]

1.549×10-19lJ is the energy of a photon emitted when an electron in a hydrogen atom undergoes a transition from =7 to =1.

The equation E= hcE =hc, where h is Planck's constant and c is the speed of light, describes the inverse relationship between a photon's energy (E) and the wavelength of light ().

The Rydberg formula is used to determine the energy change.

Rydberg's original formula used wavelengths, but we may rewrite it using units of energy instead. The result is the following.

aaΔE=R(1n2f−1n2i) aa

were

2.17810-18lJ is the Rydberg constant.

The initial and ultimate energy levels are ni and nf.

As a change of pace from

n=5 to n=3 gives us

ΔE

=2.178×10-18lJ (132−152)

=2.178×10-18lJ (19−125)

=2.178×10-18lJ×25 - 9/25×9

=2.178×10-18lJ×16/225

=1.549×10-19lJ

Learn more about Rydberg formula here-

brainly.com/question/13185515

#SPJ4

8 0

2 years ago

Dinosaurs’ skeletons can be distinguished from those of other reptiles by the structure of the hips and legs.

jeyben [28]

True, they had a hole in their hip socket that allowed them to run faster than other reptiles of their size at the time. As well as most reptiles besides reptiles had legs to the side, rather than under them like dinosaurs did.

Hope this helps!

5 0

3 years ago