All categories

3 years ago

In 2-3 sentences, explain the difference between constructive and destructive interference.

1 answer:

5 0

In constructive interference, waves that are in phase will combine together and increase the amplitude. In destructive interference, waves are out of phase and cancel one another out.

You might be interested in

What is a law in physics?

Rina8888 [55]

Answer:

By nature, laws of Physics are stated facts which have been deduced and derived based on empirical observations. Simply put, the world around us works in a certain way, and physical laws are a way of classifying that “working.”

6 0

3 years ago

What is the advantage of SI unit over CGS unit?

Allushta [10]

ADVANTAGE

PEOPLE USED CERTAIN UNIT OF MEASUREMENT IN THEIR SPECIFIC REGION WHICH IS NOT ACCEPTED BY WORLD IN CGS SYSTEM.CGS UNIT MADE

DIFFICULTY IN TRADE. LATER SI UNIT OF MEASUREMENT HAVE BEEN ADOPTED IN 1960 AD TO BRING THE uniformity IN measurement throughout THE WORLD. SI SYSTEM MADE THE MEASURENT AROUND WORLD MORE EFFECTIVE AND LESS COFUSING THAN CGS UNIT.

5 0

3 years ago

A pencil rolls horizontally of a 1 meter high desk and lands .25 meters from the base of the desk. How fast was the pencil rolli

vovikov84 [41]

Answer: 0.55 m/s

Explanation:

This situation is related to projectile motion (also called parabolic motion), where the main equations are as follows:

$x=V_{o} cos\theta t$ (1)

$y=y_{o}+Vo sin \theta t + \frac{g}{2}t^{2}$ (2)

Where:

$x=0.25 m$ is the horizontal displacement of the pencil

$V_{o}$ is the pencil's initial velocity

$\theta=0\°$ since we are told the pencil rolls <u>horizontally</u> before falling

$t$ is the time since the pencil falls until it hits the ground

$y_{o}=1 m$ is the initial height of the pencil

$y=0$ is the final height of the pencil (when it finally hits the ground)

$g=-9.8m/s^{2}$ is the acceleration due gravity, always acting vertically downwards

Begining with (1):

$x=V_{o} cos(0\°) t$ (3)

$x=V_{o}t$ (4)

Finding $t$ from (2):

$0=1 m+ \frac{-9.8m/s^{2}}{2}t^{2}$ (5)

$t=\sqrt{\frac{-2y_{o}}{g}}$ (6)

Substituting (6) in (4):

$x=V_{o}\sqrt{\frac{-2y_{o}}{g}}$ (7)

Isolating $V_{o}$ :

$V_{o}=\frac{x}{\sqrt{\frac{-2y_{o}}{g}}}$ (8)

$V_{o}=\frac{0.25 m}{\sqrt{\frac{-2(1 m)}{-9.8m/s^{2}}}}$ (9)

Finally:

$V_{o}=0.55 m/s$

4 0

4 years ago

A spherical capacitor is formed from two concentric spherical conducting shells separated by vacuum. The inner sphere has a radi

Svetlanka [38]

Answer: a) 73.41 10^-12 F; b)4.83* 10^3 N/C; c) 3.66 *10^3 N/C

Explanation: To solve this problem we have to consider the following: The Capacity= Charge/Potential Difference

As we know the capacity is value that depend on the geometry of the capacitor, in our case two concentric spheres.

So Potential Difference between the spheres is given by:

ΔV=- $\int\limits^a_b {E} \, dx$

Where E = k*Q/ r^2

so we have $\int\limits^a_b {K+Q1/r} \, dr$

then

Vb-Va=k*Q(1/b-1/a)=kQ (ab/b-a)

Finally using C=Q/ΔV=ab/(k(b-a))

To caclulate the electric firld we first obtain the charge

Q=ΔV*C=120 V*73.41 10^-12 F=8.8 10^-9 C

so E=KQ/r^2 for both values of r

r=12.8 cm ( in meters)

r2=14.7 cm

E(r1)=4.83* 10^3 N/C

E(r2)=3.66 *10^3 N/C

8 0

3 years ago

When during new product development is Design For Manufacture and Assembly (DFMA) most effective? a) At all times b) During prod

Lina20 [59]

Answer:most likely E

Explanation:

Why would anybody do something after design there done with there work after that

3 0

3 years ago