Answer:
Engineers, as practitioners of engineering, are professionals who invent, design, analyze, build and test machines, complex systems, structures, gadgets and materials to fulfill functional objectives and requirements while considering the limitations imposed by practicality, regulation, safety and cost
There are now six major branches of engineering: Mechanical, Chemical, Civil, Electrical, Management, and Geotechnical, and literally hundreds of different subcategories of engineering under each branch.
Explanation:
Answer:
Specific Weight = 76.19 lb/ft³
mass density = 34.56
specific gravity = 1.22
Explanation:
given data
weighs = 38,300 pounds
diameter = 8 ft
high = 10 ft
solution
we get here Specific Weight that is
Specific Weight = .................1
Specific Weight =
Specific Weight =
Specific Weight = 76.19 lb/ft³
and
mass density = .............2
mass density =
mass density = 34.56
and
specific gravity = ............3
specific gravity =
specific gravity = 1.22
Answer:
The force over the plane windows are 764 lbf in the EE unit system and 3398 N in the international unit system.
Explanation:
The net force over the window is calculated by multiplying the difference in pressure by the area of the window:
F = Δp*A
The pressure inside the plane is around 1 atm, hence the difference in pressure is:
Δp = 1atm - 0.35 atm = 0.65 atm
Expressing in the EE unit system:
Δp = 0.65 atm * 14.69 lbf/in^2 = 9.55 lbf/in^2
Replacing in the force:
F = 9.55 lbf/in^2 * 80 in^2 = 764 lbf
For the international unit system, we re-calculate the window's area and the difference in pressure:
A = 80 in^2 * (0.0254 m/in)^2 = 0.0516 m^2
Δp = 0.65 atm * 101325 Pa = 65861 Pa = 65861 N/m^2
Replacing in the force:
F = 65861 N/m^2 *0.0516 m^2 = 3398 N
Answer: A wall is a collection of studs (usually sized 2×4 or 2×6) equally spaced (usually 16 in. or 24 in. on center) and sandwiched between top and bottom plates. The top plate can be either single or double. Double plating is most common on load-bearing walls unless the roof rafters or trusses and floor joists stack directly over the studs in the wall, then a single top plate can be used.
Large openings in the wall are made for windows and doors. When the opening is greater in width than the stud spacing — and most windows are wider than 24 in. — then a header must be inserted to carry the load of the interrupted stud(s). A header is a simple beam sized to support the load above the opening it spans.The header is supported by a jack stud at each end. Jacks, sometimes called trimmers, fit under each end of a header, and they transfer the load that the header carries down to the bottom plate and the framing beneath. Nailed to the jacks are full-height studs called king studs; they support the assembly between the plates. Sometimes jacks must be doubled on wide openings so there’s enough supporting surface for the header to bear on. Jacks can be replaced with a steel header hanger attached to the king stud.
Saddles and cripples
A saddle (also called a sill) forms the bottom of a window opening. It’s a piece of 2x stock laid flat and nailed between the jacks. Cripples are short pieces of 2x stock that run underneath the saddle. And, depending on a header’s height, cripples can run from the header to the plate. Cripples are located at the points where a common stud would have been located had it not been interrupted by the opening.
Mike Guertin and Rick Arnold are professional builders in Rhode Island with over 20 years experience building custom homes. In addition to being contributing editors for Fine Homebuilding magazine, they have written numerous articles on homebuilding, and they conduct regular seminars for builders.
Explanation:
Answer:
the answer is the "income tax"