All categories

3 years ago

Glaciation in Alaska is a result of interactions between which of the following "spheres"? Check all that apply.

Chemistry

2 answers:

N76 [4]3 years ago

6 0

Answer:

Option (C)

Option (E)

Option (F)

Explanation:

Glaciers in a particular area forms when the temperature drops down to its freezing point. Also at the same time, the altitude areas like the mountains and the hills also accumulates ice under certain temperature conditions.

Glaciation in Alaska was taken place in the last ice age known as the Pleistocene ice age, during which most of the places were covered with ice but from the recent studies, it has been observed that the glaciers have melted and is now about to be extinct.

<u>Alaska glaciation had taken place in its geological past due to its interaction between the geosphere, atmosphere, and hydrosphere</u>.

Geosphere refers to all the region that makes up the entire earth.

The atmosphere refers to the envelope of variable gases that surrounds the earth.

Hydrosphere includes all the water bodies present on earth.

Thus, the correct options are given above.

elena-s [515]3 years ago

4 0

I would say E is the right answer.

You might be interested in

According to the periodic table, carbon has an atomic mass of 12.011 u. This indicates that the most abundant isotope of carbon

Eduardwww [97]

The most abundant of all of the isotopes of an element will be the one who's mass the mass of element is closest to. In this case, the mass of atomic carbon is closest to the mass of carbon-12.
Thus, Carbon-12 is the most abundant isotope.

3 0

3 years ago

Read 2 more answers

Which is most complicated to separate?

Sergio [31]

Answer: Atoms are the hardest substance to separate

7 0

2 years ago

Arrange the following molecules according to the strength of their dispersion forces. Organize in order from largest to smallest

ki77a [65]

Explanation:

The weak intermolecular forces which can arise either between nucleus and electrons or between electron-electron are known as dispersion forces. These forces are also known as London dispersion forces and these are temporary in nature.

Therefore, more is the surface area occupied by the carbon chain more will be the dispersion forces present in it. Hence, less is the surface area occupied by a molecule less will be the dispersion forces present in it.

Hence, the given molecules are organized from largest to smallest dispersion forces as follows.

$CH_{3}CH(CH_{3})C(CH_{3})_{2}CH_{2}CH_{3}$ > $CH_{3}CH_{2}(CH_{2})_{4}CH_{2}CH_{3}$ > $CH_{3}CH_{2}CH_{2}CH_{2}CH_{3}$ > $CH_{3}C(CH_{3})2CH_{3}$ > $CH_{3}CH_{2}CH_{3}$ > $CH4$

3 0

3 years ago

Suppose the price of gasoline increases 10% and quantity of gasoline demanded in Orlando drops 5% per day. Demand for gasoline i

grin007 [14]

Answer:

The correct answer is;

Demand for gasoline in Orlando is price inelastic.

Explanation:

The elasticity is the degree of response to a change in price or quantity supplied to the the quantity demanded. An elastic demand responds positively to change in price, while an inelastic demand means that when there is a price increase, the quantity demanded remains the same and where there is a drop in price the quantity demanded remains constant.

If a small change in price results in a large change in demand then the good is said to be price elastic

In the question the price increases by 10% while the quantity demanded drops 5 % daily. Therefore it is price inelastic

5 0

3 years ago

Which of the following factors could you change in a system and not change its induced EMF?

krok68 [10]

The options attached to the question above are listed below:
A. Magnetic field.
B. Type of wire.
C. Velocity of the wire.
D. Length of the wire in the field.

ANSWER
The correct option is B.
The factors that determine the induced current in a system are: the number of wires in the coil, the strength of the magnetic field and speed of armature rotation [speed of cutting]. Generally, the induced electromotive force across a conductor is equal to the rate at which magnetic flux is cut by the conductor. The type of wire used does not affect the induced EMF.

8 0

3 years ago

Read 2 more answers