The number of Ml of C₅H₈ that can be made from 366 ml C₅H₁₂ is 314.7 ml of C₅H₈
<u><em>calculation</em></u>
step 1: write the equation for formation of C₅H₈
C₅H₁₂ → C₅H₈ + 2 H₂
Step 2: find the mass of C₅H₁₂
mass = density × volume
= 0.620 g/ml × 366 ml =226.92 g
Step 3: find moles Of C₅H₁₂
moles = mass÷ molar mass
from periodic table the molar mass of C₅H₁₂ = (12 x5) +( 1 x12) = 72 g/mol
moles = 226.92 g÷ 72 g/mol =3.152 moles
Step 4: use the mole ratio to determine the moles of C₅H₈
C₅H₁₂:C₅H₈ is 1:1 from equation above
Therefore the moles of C₅H₈ is also = 3.152 moles
Step 5: find the mass of C₅H₈
mass = moles x molar mass
from periodic table the molar mass of C₅H₈ = (12 x5) +( 1 x8) = 68 g/mol
= 3.152 moles x 68 g/mol = 214.34 g
Step 6: find Ml of C₅H₈
=mass / density
= 214.34 g/0.681 g/ml = 314.7 ml
Answer:
May be the instrument is incorrect or may be error in it.
Explanation:
The copper have not been detected by this test because the test may be not for the detection of copper, may be it is used for identification of another minerals. If there is copper in the lake sample but can't be detected in the test so it means that the instrument which is used for detection is not the right one or having error in that instrument. Every mineral has a specific type of instrument that detect its presence, if we use incorrect instrument for the mineral then we can't detect the presence of that specific mineral.
I am sure, the answer is variant B.
Answer: Evaporation
Explanation:
When the heat of the sun touches the water, the water molecules heat up and move gradually faster. Over time molecules start to pop out the surface of the water individually.
And then eventually all the water is evaporated into water vapor.
Answer:
Explanation:
Liquid-liquid extraction is a very useful method to separate components from a mixture. It consists of separating one or several substances dissolved in a solvent by transferring them to another solvent insoluble or partially insoluble in the first. The transfer of matter is achieved by direct contact between the two liquid phases.
For the extraction process, the solution is placed in a separating funnel, a water-immiscible organic solvent is added (ethyl ether is the most used), the solution with the compound to be separated, the funnel is covered and the funnel is top. Then it shakes. Depending on the solubilities and density, different layers are observed. The denser the compound, the more it will sink.
Since the organic compound is usually much more soluble in ether than in water, most of the organic compound will be dissolved in the ether phase (upper phase) and inorganic salts, which are not soluble in ether, will remain in the aqueous phase ( lower phase). Subsequently, by separating the separating funnel the two phases are separated, the organic phase is collected.
Occasionally, after stirring, the two immiscible liquids do not separate sharply, forming an emulsion in the intermediate zone. This is called the colloidal suspension of a liquid in another (system consisting of two or more phases, usually a liquid and another dispersed in the form of generally very fine solid particles). One of the reasons for the formation of an emulsion is when the two phases have similar densities. Then the relative density of the organic solvent and water cannot always be relied upon, although there are methods to facilitate the complete separation of the two phases.
