1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
goldenfox [79]
4 years ago
12

What should you lubricate the grommets with when installing a new master cylinder reservoir?

Engineering
1 answer:
alekssr [168]4 years ago
6 0

Answer:

Install the reservoir grommets in the housing. Lubricate the area with clean brake fluid and install the reservoir. All the lettering should be properly read from the left side of the reservoir when it is properly installed. Make sure the bottom of the reservoir touches the top of the grommet

You might be interested in
Question 1
vlabodo [156]

Answer:

A. from zero at the center to maximum at the circumference.

Explanation:

The shear stress describes the process where a body deforms as a result of a part sliding over the other.

The value of shear stress which is induced in the shaft due to the applied couple varies from zero at the center to maximum at the circumference.

The shear stress in a shaft is given by this formula;

τ = Tr/I

where;

τ = shear stress (MPa).

T = applied torque (Nmm).

r = distance from center to stressed surface in the given position (mm).

I = polar moment of Inertia of cross-sectional area (mm).

3 0
3 years ago
What is tear test? What do we understand from this test? How?
Anvisha [2.4K]

Explanation:

The tear test determines the force required by a material to undergo complete failure when there is already a crack or tear present in it.

With this test we understand a material's resistance to failure when there is already a crack present.

The material which already has a crack is placed in a tensile testing or universal test machine. So, both sides of the material along the crack are pulled until material failure takes place.

6 0
4 years ago
A hair dryer is basically a duct of constant diameter in which a few layers of electric resistors are placed. A small fan pulls
Inessa05 [86]

Answer:

the percent increase in the velocity of air is 25.65%

Explanation:

Hello!

The first thing we must consider to solve this problem is the continuity equation that states that the amount of mass flow that enters a system is the same as what should come out.

m1=m2

Now remember that mass flow is given by the product of density, cross-sectional area and velocity

(α1)(V1)(A1)=(α2)(V2)(A2)

where

α=density

V=velocity

A=area

Now we can assume that the input and output areas are equal

(α1)(V1)=(α2)(V2)

\frac{V2}{V1} =\frac{\alpha1 }{\alpha 2}

Now we can use the equation that defines the percentage of increase, in this case for speed

i=(\frac{V2}{V1} -1) 100

Now we use the equation obtained in the previous step, and replace values

i=(\frac{\alpha1 }{\alpha 2} -1) 100\\i=(\frac{1.2}{0.955} -1) 100=25.65

the percent increase in the velocity of air is 25.65%

6 0
3 years ago
Given V1 = 8 vpp, R1 = 6 kΩ, V2 = 5 vpp, R2 = 3 kΩ, V3 = 10 vpp, R3 = 3 kΩ, and Rf = 14 kΩ, find Vout. Vout = vpp. (Round your a
iragen [17]

Answer:

Vout= 93.3V

Explanation:

For this question, consider circuit in the attachment 1.

This is the circuit of an inverting amplifier. In an inverting amplifier

Vout/Vin= -Rf/Rin

To calculate the Vout, we must find Rin and Vin. For this we must solve the input circuit (attachment 2)  using  Thevinine theorem. Thevnine theorem states that all voltage sources in a circuit can be replaced by an equivalent voltage source Veq and and all resistances can be replaced by an equivalent resistance Req. To find out Req all voltage sources must be short circuited (attachment 3)

1/Req= 1/R1+1/R2+1/R3

1/Req=1/6+1/3+1/3

Req=6/5

To find out Veq consider circuit in attachment 4. We will solve this circuit using nodal analysis. In nodal analysis, we use the concept that sum of currents entering a node is equal to the sum of currents leaving a node. So,

I1= I2+I3

(10-Veq)/6= (Veq-5)/3+(Veq-10)/3

Veq=8V

Now the input circuit can be simplified as shown in attachment 5. Solve for Vout using equation

Vout/Veq= -Rf/Req

Vout/8= -14/(6/5)

Vout= - 93.3

It is at an angle of 180° from Veq

7 0
3 years ago
What does a block tester do?
tatyana61 [14]

Answer:

Block design test. A block design test is a subtest on many IQ test batteries used as part of assessment of human intelligence. It is thought to tap spatial visualization ability and motor skill.

Explanation:

6 0
3 years ago
Other questions:
  • 6.8.1: Function pass by pointer: Transforming coordinates. Define a function CoordTransform() that transforms its first two inpu
    9·1 answer
  • A meter stick can be read to the nearest millimeter and a travelling microscope can be read to the nearest 0.1 mm. Suppose you w
    11·1 answer
  • Scenario* The organization is a regional XYZ Credit Union/Bank that has multiple branches and locations throughout the region.*
    9·1 answer
  • The function of a circuit breaker is to _____.
    12·1 answer
  • 5.16 A power cycle operating between hot and cold reservoirs at 500 K and 300 K, respectively, receives 1000 kJ by heat transfer
    11·1 answer
  • A 3 m aluminum pole is kept at a residential site for construction
    12·1 answer
  • Can somebody help me
    9·1 answer
  • The "Big Dig" was the nickname of the civil engineering project that redesigned the highway Infrastructure for the city of
    7·1 answer
  • A. Briefly describe the microstructural difference between spheroidite and tempered martensite. Explain why tempered martensite
    14·1 answer
  • Ký hiệu của vật liệu cơ khí
    15·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!