All categories

2 years ago

What is hydraulic pressure?

1 answer:

3 0

Hydraulic pressure is actually the pressure that is exerted to liquid and the pressure gets transmitted throughout the liquid. Since liquid cannot be compressed, so the pressure that was exerted on the liquid gets transmitted to the walls of the container containing the liquid. This theory is applied to the braking system of cars and some other vehicles. This is known as the hydraulic pressure. It is actually the science that is concerned with the laws of movements of a fluid and the application of this theory for engineering purpose. This theory has not only been used in cars but also in planes .

You might be interested in

QUICK!! What class of leer is shown below?

wlad13 [49]

Answer:

3rd class lever

HOPE IT HELPS YOU OUT PLEASE MARK IT AS BRAINLIEST AND FOLLOW ME PROMISE YOU TO FOLLOW BACK ON BRAINLY.IN

5 0

2 years ago

Read 2 more answers

ou purchase a rectangular piece of metal that has dimen- sions 5.0 * 15.0 * 30.0 mm and mass 0.0158 kg. The seller tells you tha

Natalija [7]

Answer: 7022.2kg/m³, yes, I was cheated

Explanation:

Density of an object is defined as the ratio of the mass of the object to its volume. Mathematically;

Density = Mass/Volume

Note that the unit of both mass and volume must be standard unit.

Given mass = 0.0158kg

Dimension of the metal = 5mm×15mm×30mm

Note that 1mm = 0.001m

The volume of the metal will be

0.005×0.015×0.03

= 0.00000225m³

Density = 0.0158/0.00000225

Average density of the metal = 7022.2kg/m³

Since the standard density of Gold is 19,320kg/m³ and is higher than the density prescribed for me, it shows the I was cheated.

4 0

3 years ago

Me amor

Oxana [17]

Answer:

jajajaja

Explanation:

7 0

2 years ago

What is the gauge pressure of the water right at the point p, where the needle meets the wider chamber of the syringe? neglect t

Helen [10]

Missing details: figure of the problem is attached.

We can solve the exercise by using Poiseuille's law. It says that, for a fluid in laminar flow inside a closed pipe,

$\Delta P = \frac{8 \mu L Q}{\pi r^4}$

where:

$\Delta P$ is the pressure difference between the two ends

$\mu$ is viscosity of the fluid

L is the length of the pipe

$Q=Av$ is the volumetric flow rate, with $A=\pi r^2$ being the section of the tube and $v$ the velocity of the fluid

r is the radius of the pipe.

We can apply this law to the needle, and then calculating the pressure difference between point P and the end of the needle. For our problem, we have:

$\mu=0.001 Pa/s$ is the dynamic water viscosity at $20^{\circ}$

L=4.0 cm=0.04 m

$Q=Av=\pi r^2 v= \pi (1 \cdot 10^{-3}m)^2 \cdot 10 m/s =3.14 \cdot 10^{-5} m^3/s$

and r=1 mm=0.001 m

Using these data in the formula, we get:

$\Delta P = 3200 Pa$

However, this is the pressure difference between point P and the end of the needle. But the end of the needle is at atmosphere pressure, and therefore the gauge pressure (which has zero-reference against atmosphere pressure) at point P is exactly 3200 Pa.

8 0

2 years ago

A spaceship ferrying workers to Moon Base I takes a straight-line path from the earth to the moon, a distance of 384,000 km. Sup

Tema [17]

Answer:

a) v = 19,149.6 m/s

b) f = 95%

c) t = 346.5min

Explanation:

First put all values in metric units:

$15.8 min*\frac{60s}{1min}=948s$

The equation of motion you need is:

$v_f = a*t+v_0$

where $v_f$ is the final velocity, a is acceleration and t is time in hours.

Since the spaceship starts from 0 velocity:

$v_f = a*t = 20.2*948 = 19,149.6 m/s$

Next, you need to calculate the distances traveled on each interval, considering that both starting and final intervals travel the same distance because the acceleration and time are equal. For this part you need the next motion equation:

$x=\frac{v_0+v_f}{2}t$