The git _____ command allows us to record (aka track or stage) changes have been made in our git repository.

Five bolts are used in the connection between the axial member and the support. The ultimate shear strength of the bolts is 320

lesya [120]

Answer:

The minimum allowable bolt diameter required to support an applied load of P = 450 kN is 45.7 milimeters.

Explanation:

The complete statement of this question is "Five bolts are used in the connection between the axial member and the support. The ultimate shear strength of the bolts is 320 MPa, and a factor of safety of 4.2 is required with respect to fracture. Determine the minimum allowable bolt diameter required to support an applied load of P = 450 kN"

Each bolt is subjected to shear forces. In this case, safety factor is the ratio of the ultimate shear strength to maximum allowable shear stress. That is to say:

$n = \frac{S_{uts}}{\tau_{max}}$

Where:

$n$ - Safety factor, dimensionless.

$S_{uts}$ - Ultimate shear strength, measured in pascals.

$\tau_{max}$ - Maximum allowable shear stress, measured in pascals.

The maximum allowable shear stress is consequently cleared and computed: ( $n = 4.2$ , $S_{uts} = 320\times 10^{6}\,Pa$ )

$\tau_{max} = \frac{S_{uts}}{n}$

$\tau_{max} = \frac{320\times 10^{6}\,Pa}{4.2}$

$\tau_{max} = 76.190\times 10^{6}\,Pa$

Since each bolt has a circular cross section area and assuming the shear stress is not distributed uniformly, shear stress is calculated by:

$\tau_{max} = \frac{4}{3} \cdot \frac{V}{A}$

Where:

$\tau_{max}$ - Maximum allowable shear stress, measured in pascals.

$V$ - Shear force, measured in kilonewtons.

$A$ - Cross section area, measured in square meters.

As connection consist on five bolts, shear force is equal to a fifth of the applied load. That is:

$V = \frac{P}{5}$

$V = \frac{450\,kN}{5}$

$V = 90\,kN$

The minimum allowable cross section area is cleared in the shearing stress equation:

$A = \frac{4}{3}\cdot \frac{V}{\tau_{max}}$

If $V = 90\,kN$ and $\tau_{max} = 76.190\times 10^{3}\,kPa$ , the minimum allowable cross section area is:

$A = \frac{4}{3} \cdot \frac{90\,kN}{76.190\times 10^{3}\,kPa}$

$A = 1.640\times 10^{-3}\,m^{2}$

The minimum allowable cross section area can be determined in terms of minimum allowable bolt diameter by means of this expression:

$A = \frac{\pi}{4}\cdot D^{2}$

The diameter is now cleared and computed:

$D = \sqrt{\frac{4}{\pi}\cdot A}$

$D =\sqrt{\frac{4}{\pi}\cdot (1.640\times 10^{-3}\,m^{2})$

$D = 0.0457\,m$

$D = 45.7\,mm$

The minimum allowable bolt diameter required to support an applied load of P = 450 kN is 45.7 milimeters.

5 0

3 years ago

What are the benefits of using the engineering design process

Shalnov [3]

Answer:

Some of the benefits are tangible for they are visible in the design and production process, while the other benefits are intangible which may not be visible directly but result in improvement in the quality of product, better control over designing and production process, reduction of stress on the designers etc.

7 0

3 years ago

Write a Python program that does the following. Create a string that is a long series of words separated by spaces. The string i

dybincka [34]

Answer:

The code is attached.

Explanation:

I created a string s including 6 colors with spaces in between. Then I converted the string into a list x by using split() method. I used three different methods for removing elements from the list. These methods are remove(), pop() and del.

$\\$ Then I used methods append(), insert() and extend() for adding elements to the list.