All categories

3 years ago

PLEASE HELP! ASAP!!!!

1 answer:

4 0

The answer should be B.

Prevailing winds are likely from the north.

Windward vs. leeward sides would create infiltration on one side and exfiltration on the other.

Should do a before and after on the same window under same conditions. Wind, ambient temperature, etc.

You might be interested in

Precast concrete curtain wall panels: Group of answer choices are typically manufactured on site and then hoisted into place. of

amid [387]

Answer:

c) can be made with a variety of surface finishes.

Explanation:

The missing options are;

When it comes to concrete work in construction, the concrete can be cast either in-situ or in form of pre-cast concrete.

Now in-situ concrete means concrete done on the construction site being built while pre cast concrete simply means concrete cast outside in a factory or yard and brought to site to mount.

These pre cast concrete could have different surface finishes as required as this is one of it's advantages over in situ because there is a lot of space and room to have the desired concrete finish.

a) are typically manufactured on site and then hoisted into place.

b) cannot be fiber-reinforced.

c) can be made with a variety of surface finishes.

d) never include insulation.

e) often are unreinforced.

5 0

2 years ago

1 A power transmission includes a belt drive, a chain drive and a gear drive. Which of the following is the best arrangement bet

Setler79 [48]

Answer:d

Explanation:

(d) chain drive belt drive gear drive

3 0

3 years ago

Bridging are members installed periodically between joists to ensure which of the following?

Pie

Answer:

Distributes a floor load or weight

Explanation:

5 0

3 years ago

Which of the following is true about modern hydraulic lifts?

kaheart [24]

The modern hydraulic lifts make use of biodegradable fluid to transmit hydraulic power

Question: The options are left out in the question. The details and facts about the modern hydraulic lift are presented here

Details about the modern hydraulic lifts include;

The development of the modern hydraulic occurred in the Industrial Revolution to perform task done previously by steam powered elevators

The power of the hydraulic lift come from the hydraulic cylinder known as the actuator, which in turn is powered by pressurized hydraulic fluid such as oil

The hydraulic fluid is pushed by a piston rod through which energy is capable of being transferred, such that the applied force is multiplied, to provide more power for lifting

Facts about the modern hydraulic lifts include;

The dry motor in the modern hydraulic lift is more efficient and consumes 20% less energy

It comprises of valves that are controlled electronically such that the response is much rapid and the energy consumption is reduced by a further 20%

The cars used in the modern lift are lighter, as well as the slings, which reduces the power usage by 20%

It makes use of chemicals which are environmentally friendly as hydraulic fluid

The flash point of the fluid used is higher, as well as it posses 50% lower compressibility as well elasticity

Learn more here:

brainly.com/question/16942803

6 0

2 years ago

When subject to an unknown torque, the shear stress in a 2 mm thick rectangular tube of dimension 100 mm x 200 mm was found to b

laila [671]

Answer:

The shear stress will be 80 MPa

Explanation:

Here we have;

τ = (T·r)/J

For rectangular tube, we have;

Average shear stress given as follows;

Where;

$\tau_{ave} = \frac{T}{2tA_{m}}$

$A_m$ = 100 mm × 200 mm = 20000 mm² = 0.02 m²

t = Thickness of the shaft in question = 2 mm = 0.002 m

T = Applied torque

Therefore, 50 MPa = T/(2×0.002×0.02)

T = 50 MPa × 0.00008 m³ = 4000 N·m

Where the dimension is 50 mm × 250 mm, which is 0.05 m × 0.25 m

Therefore, $A_m$ = 0.05 m × 0.25 m = 0.0125 m².

Therefore, from the following average shear stress formula, we have;

$\tau_{ave} = \frac{T}{2tA_{m}}$

Plugging in then values, gives;

$\tau_{ave} = \frac{4000}{2\times 0.002 \times 0.0125} = 80,000,000 Pa$

The shear stress will be 80,000,000 Pa or 80 MPa.

7 0

3 years ago