All categories

3 years ago

a straight line on a graph means there is a _________ relationship between the dependent variable and the independent variable

Physics

2 answers:

Zarrin [17]3 years ago

5 0

Answer:

Direct relationship

Explanation:

A straight line graph can be referred to as a linear graph. This relationship shows that a change in the value of the dependent variable would cause a change in the value of independent variable at the same rate.

A straight line graph in a cartesian coordinate convey structure and represent stability.

Nady [450]3 years ago

4 0

By definition this is a linear relationship.

You might be interested in

A flashlight converts?

sammy [17]

Answer:

Energy conversion in flashlight.

Explanation:

When the switch of a flashlight is on, then the batteries inside them will be connected in a circuit and chemical energy from the batteries will be converted into electrical energy and then the electrical energy will be converted into light energy.

Light energy is also called electromagnetic energy.

Hence, among the given options the correct one is the first option that is:

1. Electrical energy into electromagnetic energy is the answer.

4 0

3 years ago

According to kinetic molecular theory, which statement best describes collisions between gas particles?

Mkey [24]

A they are elastic.
being in random motion means they're not predictable.
being elastic, they don't stick together

5 0

3 years ago

A composite load consists of three loads connected in parallel. One draws 100 W at a PF of 0.92 lagging, another takes 250 W at

fenix001 [56]

Answer:

a) $I_{RMS} = 4.79 A$

b) $PF = 0.908$

Explanation:

Get the reactive powers for each of the loads:

Reactive power = Real Power * tanθ

For load 1

Active power, P₁ = 100 W

Power factor, $cos \theta_{1} = 0.92$

$\theta_{1} = cos^{-1} 0.92\\\theta_{1} = 23.074$

$Q_{1}= P_{1} tan \theta_{1} \\Q_{1}= 100tan 23.074\\Q_{1}= 42.60 W$

For load 2

Active power, P₂ = 250 W

Power factor, $cos \theta_{2} = 0.8$

$\theta_{2} = cos^{-1} 0.8\\\theta_{2} = 36.87$

$Q_{2}= P_{1} tan \theta_{2} \\Q_{2}= 250tan 36.87\\Q_{2}= 187.5 W$

For load 3

Active power, P₃ = 250 W

Power factor, $cos \theta_{3} = 1$

$\theta_{3} = cos^{-1} 1\\\theta_{3} =0$

$Q_{2}= P_{1} tan \theta_{3} \\Q_{3}= 150tan 0\\Q_{3}= 0 W$

Calculate the total reactive power, $Q_{net} = 42.6 + 187.5 + 0$

$Q_{net} = 230.1 W$

Calculate the total active power, $P_{net} = 100 + 250 + 150 = 500 W$

$S_{net} = P_{net} + Q_{net} \\S_{net} = 500 + j230.1$

$P_{net} = IVcos \theta_{net}$

$\theta_{net} = tan^{-1} \frac{230.1}{500} \\\theta_{net} = 24.712$

V = 115 $V_{rms}$

$500 = I_{RMS} * 115 cos 24.712\\I_{RMS} = 500/104.47\\ I_{RMS} = 4.79 A$

b) Power factor of the composite load is $cos\theta_{net}$

$\theta_{net} = 24.712\\PF = cos 24.712\\PF = 0.908$

4 0

3 years ago

Stu wanted to calculate the resistance of a light bulb

Nonamiya [84]

Answer:

yes

Explanation:

He used the formula R = VI and obtained an

answer of 2

3 0

3 years ago

Read 2 more answers

Consider the medium of air as defined by the use of radio frequency. What made some of the early standards so slow compared to t

Tanzania [10]

Answer:

Explanation:

Earliest standards were dependent on a single frequency/channel to both send and receive. This shared medium creates the same problem as half-duplex coax cable. Because receivers had to wait for the signal before sending a response, this reduced the overall bandwidth.

Other factors affect wireless signal propagation, too, including RF interference, antenna choice, and obstacles such as walls, trees, and even weather (precipitation, for example).

3 0

4 years ago