All categories

3 years ago

Disadvantages of friction

Physics

1 answer:

liraira [26]3 years ago

4 0

Answer:

Produces heat in various parts of machines.

Due to friction we have to exert more power in machines.

It opposes the motion.

Due to friction, noise is also produced in machines.

Due to friction, engines of automobiles consume more fuel which is a money loss.

Explanation:

Source: https://www.quora.com/What-are-the-disadvantages-of-friction

You might be interested in

What is the characteristic that allows an object to have kinetic energy?

Shtirlitz [24]

Kinetic energy is movement, thus movement would be a characteristic that allows an object to have kinetic energy

6 0

3 years ago

you are piloting a small plane and you want to reach an airport 450 km due south in 3.0 h a wind is blowing from the west 50.0 k

alex41 [277]

Answer:

You should choose airspeed 158.11 km/h at 18.4° west of south

Explanation:

The distance to the air port is 450 km due to south

You should to reach the airport in 3 hours

→ Velocity = distance ÷ time

→ Distance = 450 km , time = 3 hours

→ The velocity of your plane = 450 ÷ 3 = 150 km/h due to south

A wind is blowing from west 50 km/h

We need to know what heading and airspeed you should choose to

reach your destination

At first we must find the resultant velocity of your plane and the wind

The south and west are perpendicular, then the resultant velocity is

→ $v_{R}=\sqrt{(v_{p})^{2}+(v_{w})^{2}}$

→ $v_{p}=150$ km/h , $v_{w}=50$ km/h

→ $v_{R}=\sqrt{(150)^{2}+(50)^{2}}=158.11$ km/h

To cancel the velocity of the wind, the pilot should maintain the velocity

of the plane at 158.11 km/h

The direction of the velocity is the angle between the resultant velocity

and the vertical (south)

→ The direction of the velocity is $tan^{-1}\frac{50}{150}=18.4$ °

The direction of the velocity is 18.4° west of south

<em>You should choose airspeed 158.11 km/h at 18.4° west of south</em>

8 0

3 years ago

What is the saturated zone

uranmaximum [27]

Answer:

Saturated zone is area below the water table in which the soil is completely saturated with groundwater.

Explanation:

The saturated zone lies below the ground. It is mainly the lower zone of rock along with the water table where pore spaces are completely filled with water. Even the saturated zone is sometimes separated into 2 subzones: the phreatic zone and the capillary fringe.

The area where pores spaces are not saturated with water is also unsaturated zone. Localized saturated zones can occur within the unsaturated zone. The unsaturated zone lies above the groundwater table.

6 0

3 years ago

A solenoid is designed to produce a magnetic field of 3.50×10^−2 T at its center. It has a radius of 1.80 cm and a length of 46.

Anna11 [10]

Answer:

a. 2143 turns/m

b. 111.5 m

Explanation:

a. The minimum number of turns per unit length (N/L) can be found using the following equation:

$B = \frac{\mu_{0}NI}{L}$

$\frac{N}{L} = \frac{B}{\mu_{0}I} = \frac{3.50 \cdot 10^{-2} T}{4\pi \cdot 10^{-7} Tm/A*13.0 A} = 2143 turns/m$

Hence, the minimum number of turns per unit length is 2143 turns/m.

b. The total length of wire is the following:

$N = 2143 turns/m*L = 2143 turns/m*46.0 \cdot 10^{-2} m = 986 turns$

Since each turn has length 2πr of wire, the total length is:

$L_{T} = N*2\pi r = 986 turn*2*\pi*1.80 \cdot 10^{-2} m = 111.5 m$

Therefore, the total length of wire required is 111.5 m.

I hope it helps you!

4 0

3 years ago

When a roller coaster gets to the bottom of a descent, describe the energy transfers and changes to energy stores that happen if

Feliz [49]

Answer:

its B

Explanation:

It's B & A at the same time because A. a roller coaster uses brakes to slow down and stop. B is the most reasonable answer. Because all roller coasters go up and over a second time over the hill, but they also slow down. But go with B.

TELL ME IF I´M RITE

6 0

3 years ago