Ask question

Ask question

All categories

3 years ago

14

I’m doing a project on renewable energy. There are 6 energy sources. Solar, wind, geothermal, hydroelectric, tidal, and biomass.

The thing is that I need to come up with a brand new and creative energy source. Would be glad if someone helped. Will mark brainlist.

2 answers:

nalin [4]3 years ago

6 0

Answer:

"Biofuels"

Explanation:

I don't know if this counts but I guess it's not one of those.

Verdich [7]3 years ago

4 0

It would be biogas. Sowwy if I’m wrong

You might be interested in

Imagine you are making a pizza, you start of with the dough for the crust in a large ball. You then begin to roll out the pizza

DochEvi [55]

Answer: The force exerted on the dough.

Explanation:

The force is responsible for stimulating the stress.

Recall that:

stress= Tensile force/area.

5 0

3 years ago

For a cylindrical annulus whose inner and outer surfaces are maintained at 30 ºC and 40 ºC, respectively, a heat flux sensor mea

miskamm [114]

Answer:

$k=0.12\ln(r_2/r_1)$ $\frac {W}{ m^{\circ} C}$

where $r_1$ and $r_2$ be the inner radius, outer radius of the annalus.

Explanation:

Let $r_1$ , $r_2$ and $L$ be the inner radius, outer radius and length of the given annulus.

Temperatures at the inner surface, $T_1=30^{\circ}C\\$ and at the outer surface, $T_2=40^{\circ}C$ .

Let q be the rate of heat transfer at the steady-state.

Given that, the heat flux at r=3cm=0.03m is

$40 W/m^2$ .

$\Rightarrow \frac{q}{(2\pi\times0.03\times L)}=40$

$\Rightarrow q=2.4\pi L \;W$

This heat transfer is same for any radial position in the annalus.

Here, heat transfer is taking placfenly in radial direction, so this is case of one dimentional conduction, hence Fourier's law of conduction is applicable.

Now, according to Fourier's law:

$q=-kA\frac{dT}{dr}\;\cdots(i)$

where,

K=Thermal conductivity of the material.

T= temperature at any radial distance r.

A=Area through which heat transfer is taking place.

Here, $A=2\pi rL\;\cdots(ii)$

Variation of temperature w.r.t the radius of the annalus is

$\frac {T-T_1}{T_2-T_1}=\frac{\ln(r/r_1)}{\ln(r_2/r_1)}$

$\Rightarrow \frac{dT}{dr}=\frac{T_2-T_1}{\ln(r_2/r_1)}\times \frac{1}{r}\;\cdots(iii)$

Putting the values from the equations (ii) and (iii) in the equation (i), we have

$q=\frac{2\pi kL(T_1-T_2)}{\LN(R_2/2_1)}$

$\Rightarrow k= \frac{q\ln(r_2/r_1)}{2\pi L(T_2-T_1)}$

$\Rightarrow k=\frac{(2.4\pi L)\ln(r_2/r_1)}{2\pi L(10)}$ [as $q=2.4\pi L$ , and $T_2-T_1=10 ^{\circ}C$ ]

$\Rightarrow k=0.12\ln(r_2/r_1)$ $\frac {W}{ m^{\circ} C}$

This is the required expression of k. By putting the value of inner and outer radii, the thermal conductivity of the material can be determined.

7 0

3 years ago

How does the "E" in STEM work with the other letters

KIM [24]

Answer:

if you are speaking of the acronym then Engineering uses science and mathematics to solve everyday problems in society

4 0

4 years ago

A 50 mm diameter shaft is subjected to a static axial load of 160 kN. If the yield stress of the material is 350 MPa, the ultima

zvonat [6]

In order to develop this problem it is necessary to take into account the concepts related to fatigue and compression effort and Goodman equation, i.e, an equation that can be used to quantify the interaction of mean and alternating stresses on the fatigue life of a materia.

With the given data we can proceed to calculate the compression stress:

$\sigma_c = \frac{P}{A}$

$\sigma_c = \frac{160*10^3}{\pi/4*0.05^2}$

$\sigma_c = 81.5MPa$

Through Goodman's equations the combined effort by fatigue and compression is expressed as:

$\frac{\sigma_a}{S_e}+\frac{\sigma_c}{\sigma_u}=\frac{1}{Fs}$

Where,

$\sigma_a=$ Fatigue limit for comined alternating and mean stress

$S_e =$ Fatigue Limit

$\sigma_c=$ Mean stress (due to static load)

$\sigma_u =$ Ultimate tensile stress

$Fs =$ Security Factor

We can replace the values and assume a security factor of 1, then

$\frac{\sigma_a}{320}+\frac{81.5}{400}=\frac{1}{1}$

Re-arrenge for $\sigma_a$

$\sigma_a = 254.8Mpa$

We know that the stress is representing as,

$\sigma_a = \frac{M_c}{I}$

Then,

Where $M_c$ =Max Moment

I= Intertia

The inertia for this object is

$I=\frac{\pi d^4}{64}$

Then replacing and re-arrenge for $M_c$

$M_c = \frac{\sigma_a*\pi*d^3}{32}$

$M_c = \frac{260.9*10^6*\pi*0.05^3}{32}$

$M_c = 3201.7N.m$

Thereforethe moment that can be applied to this shaft so that fatigue does not occur is 3.2kNm

5 0

4 years ago

Tensile testing provides engineers with the ability to verify and establish material properties related to a specific material.

Sedbober [7]

Answer:

True

Explanation:

Tensile testing which is also referred to as tension testing is a process which materials are subjected to so as to know how well it can be stretched before it reaches breaking point. Hence, the statement in the question is true

7 0

3 years ago