The 2 hormones are insulin & glucagon.
A hormone will only act on a part of the body it 'fits'. A hormone can be thought of as a key, and its target site ( i.e an organ) has specially shaped locks on the cell walls.
If the hormone fits, then it will work.
The hormone can set off a cascade of other singling pathways in the cell to cause an immediate effect ( for instance, insulin signaling leads to a rapid uptake of glucose in muscle cells)
The endocrine system is a tightly regulated system that keeps the hormones and their effects at just the right level. One way this is achieved is through ' feedback loops'. The release of hormones is regulated by other hormones, proteins or neuronal signals.
The released hormone then has its effect on other organs. This effect on the organ feeds back to the original signal to control any further hormone release.
btw- found all this info @ the Better Health channel, an australian government health website , so if your still confused by my answer, check out this website
www.betterhealth.vic.gov.au/health/conditionsandtreatments/hormonal-endocrine-system
Answer:
Re=309926.13
Explanation:
density=92.8lbm/ft3*(0.45kg/1lbm)*(1ft3/0.028m3)=1491.43kg/m3
viscosity=4.1cP*((1*10-3kg/m*s)/1cP)=0.0041kg/m*s
velocity=237ft/min*(1min/60s)*(0.3048m/1ft)=1.2m/s
diameter=28inch*(0.0254m/1inch)=0.71m
Re=(density*velocity*diameter)/viscosity=(1491.43kg/m3*1.2m/s*0.71m)/0.0041kg/m*s
Re=309926.13
Answer:
Half-reactions:
Cr³⁺ + 1e⁻ → Cr²⁺; Zn → Zn²⁺ + 2e⁻
Net ionic equation:
2Cr³⁺ + Zn → 2Cr²⁺ + Zn²⁺
Explanation:
The Cr³⁺ is reduced to Cr²⁺:
<h3>
Cr³⁺ + 1e⁻ → Cr²⁺ -Half-reaction 1-</h3>
Zn is oxidized to Zn²⁺:
<h3>
Zn → Zn²⁺ + 2e⁻ -Half-reaction 2-</h3>
Twice the reduction of Cr:
2Cr³⁺ + 2e⁻ → 2Cr²⁺
Now this reaction + Oxidation of Zn:
2Cr³⁺ + 2e⁻ + Zn → 2Cr²⁺ + Zn²⁺ + 2e⁻
<h3>2Cr³⁺ + Zn → 2Cr²⁺ + Zn²⁺ - Net ionic equation</h3>
The purpose of using distilled water in the cuvette of the spectrophotometer is to calibrate the instrument. It is generally considered that distilled water shows zero absorbance and 100 % transmittance. So, to zero out the absorbance of compounds other than the analyte being determined, distilled water is used as a blank.
If the unknown being determined is prepared using ethanol as the base solution, the blank used must be ethanol. This is because absorbance if any from the solvent, ethanol must be zeroed out as when the measurement of the actual unknown is being made, the absorbance of the solvent does not interfere.
Answer: <span>A fewer number of particles of the sample will dissolve in 1 minute.
That is because normally the solubility and rate of solubility of the salts in water increase with the temperature. This is, the higher the temperature the higher and faster the number of particles that the water can dissolve. So, at 70°C more particles will be dissolved in water in 1 minute than at 20°C.
</span>