All categories

2 years ago

When conducting an immediate charge on 2023 ariya, what is the first step if the timer is set?.

1 answer:

4 0

The first step to perform when conducting an immediate charge is to press the immediate charge switch on the lower left dash.

<h3>What is an immediate charge?</h3>

This is a vehicle component that allows a quick control of the machine.

However, the first step to achieve when executing an immediate charge is to press the immediate charge switch on the more low left dash.

You might be interested in

The statement that is NOT true about the concept of a boundary layer on an object is: a. the Reynolds number is greater than uni

Ilya [14]

Answer:

Option E

Explanation:

All the given statements are true except the velocity gradients normal to the flow direction are small since these are not normally small. It's true that viscous effects are present only inside the boundary layer and the fluid velocity equals the free stream velocity at the edge of the boundary layer. Moreover, Reynolds number is greater than unity and the fluid velocity is zero at the surface of the object.

5 0

2 years ago

A light bulb is switched on and within a few minutes its temperature becomes constant. Is it at equilibrium or steady state.

EleoNora [17]

Answer:

The temperature attains equilibrium with the surroundings.

Explanation:

When the light bulb is lighted we know that it's temperature will go on increasing as the filament of the bulb has to constantly dissipates energy during the time in which it is on. Now this energy is dissipated as heat as we know it, this heat energy is absorbed by the material of the bulb which is usually made up of glass, increasing it's temperature. Now we know that any object with temperature above absolute zero has to dissipate energy in form of radiations.

Thus we conclude that the bulb absorbs as well as dissipates it's absorbed thermal energy. we know that this rate is dependent on the temperature of the bulb thus it the temperature of the bulb does not change we can infer that an equilibrium has been reached in the above 2 processes i.e the rate of energy absorption equals the rate of energy dissipation.

Steady state is the condition when the condition does not change with time no matter whatever the surrounding conditions are.

6 0

3 years ago

A cylindrical insulation for a steam pipe has an inside radius rt = 6 cm, outside radius r0 = 8 cm, and a thermal conductivity k

goldfiish [28.3K]

Answer:

heat loss per 1-m length of this insulation is 4368.145 W

Explanation:

given data

inside radius r1 = 6 cm

outside radius r2 = 8 cm

thermal conductivity k = 0.5 W/m°C

inside temperature t1 = 430°C

outside temperature t2 = 30°C

to find out

Determine the heat loss per 1-m length of this insulation

solution

we know thermal resistance formula for cylinder that is express as

Rth = $\frac{ln\frac{r2}{r1}}{2 \pi *k * L}$ .................1

here r1 is inside radius and r2 is outside radius L is length and k is thermal conductivity

heat loss is change in temperature divide thermal resistance

Q = $\frac{t1- t2}{\frac{ln\frac{r2}{r1}}{2 \pi *k * L}}$

Q = $\frac{(430-30)*(2 \pi * 0.5 * 1}{ln\frac{8}{6} }$

Q = 4368.145 W

so heat loss per 1-m length of this insulation is 4368.145 W

4 0

3 years ago

A person walks into a refrigerated warehouse with head uncovered. Model the head as a 25- cm diameter sphere at 35°C with a surf

galina1969 [7]

Answer:

Hello some parts of your question is missing below is the missing part

Convection coefficient = 11 w/m^2. °c

answer : 44.83 watts

Explanation:

Given data :

surface emissivity ( ε )= 0.95

head ( sphere) diameter( D ) = 0.25 m

Temperature of sphere( T ) = 35° C

Temperature of surrounding ( T∞ ) = 25°C

Temperature of surrounding surface ( Ts ) = 15°C

б = ( 5.67 * 10^-8 )

Determine the total rate of heat loss

First we calculate the surface area of the sphere

As = $\pi D^{2}$

= $\pi * 0.25^2$ = 0.2 m^2

next we calculate heat loss due to radiation

Qrad = ε * б * As( $T^{4} - T^{4} _{s}$ ) ---- ( 1 )

where ;

ε = 0.95

б = ( 5.67 * 10^-8 )

As = 0.2 m^2

T = 35 + 273 = 308 k

Ts = 15 + 273 = 288 k

input values into equation 1

Qrad = 0.95 * ( 5.67 * 10^-8 ) * 0.2 ( (308)^4 - ( 288)^4 )

= 22.83 watts

Qrad ( heat loss due to radiation ) = 22.83 watts

calculate the heat loss due to convection

Qconv = h* As ( ΔT )

= 11*0.2 ( 35 -25 ) = 22 watts

Hence total rate of heat loss

= 22 + 22.83

= 44.83 watts

5 0

3 years ago

Calculate the volume of a hydraulic accumulator capable of delivering 5 liters of oil between 180 and 80 bar, using as a preload

Vinil7 [7]

Answer:

1) $V_o = 10 liters$

2) $V_o = 12.26 liters$

Explanation:

For isothermal process n =1

$V_o =\frac{\Delta V}{(\frac{p_o}{p_1})^{1/n} -(\frac{p_o}{p_2})^{1/n}}$

$V_o = \frac{5}{[\frac{72}{80}]^{1/1} -[\frac{72}{180}]^{1/1}}$

$V_o = 10 liters$

calculate pressure ratio to determine correction factor

$\frac{p_2}{p_1} =\frac{180}{80} = 2.25$

correction factor for calculate dpressure ration for isothermal process is

c1 = 1.03

$actual \ volume = c1\times 10 = 10.3 liters$

b) for adiabatic process

n =1.4

volume of hydraulic accumulator is given as

$V_o =\frac{\Delta V}{[\frac{p_o}{p_1}]^{1/n} -[\frac{p_o}{p_2}]^{1/n}}$

$V_o = \frac{5}{[\frac{72}{80}]^{1/1.4} -[\frac{72}{180}]^{1/1.4}}$

$V_o = 12.26 liters$

calculate pressure ratio to determine correction factor

$\frac{p_2}{p_1} =\frac{180}{80} = 2.25$

correction factor for calculate dpressure ration for isothermal process is

c1 = 1.15

$actual \volume = c1\times 10 = 11.5 liters$

8 0

3 years ago