1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Neko [114]
3 years ago
8

If a step-up transformer has a primary coil with 15 turns, how many turns would be required in the secondary coil in order to in

crease the voltage from 80 volts to 160 volts? A. 8 turns B. 30 turns C. 80 turns D. 160 turns
Physics
1 answer:
vagabundo [1.1K]3 years ago
4 0

Answer:

N_2=30turns

So option (b) will be correct option

Explanation:

We have given that there is a step up transformer in which number of turns in primary coil is 15

That is, N_1=15

Primary voltage V_1=80volt, and secondary voltage V_2=160volt

We have to find the number of turns in the secondary \

We know that for the transformer

\frac{N_1}{N_2}=\frac{V_1}{V_2}

\frac{15}{N_2}=\frac{80}{160}

N_2=30turns

So option (b) will be correct option

You might be interested in
A gate at the bottom of a dam is 10 ft tall by 30 ft wide. The specific weight of the water is 62.4 lbf/ft3. If the water is 50
Burka [1]

Answer:

The total force is most nearly 940,000lbf

Explanation:

Total force = specific weight × volume

Volume = length × width × depth = 10ft × 30ft × 50ft = 15,000ft^3

Total force = 62.4lbf/ft^3 × 15,000ft^3 = 936,000lbf which is most nearly 940,000lbf

4 0
4 years ago
A 23 g bullet traveling at 230 m/s penetrates a 2.0 kg block of wood and emerges cleanly at 170 m/s. If the block is stationary
Ann [662]

The distance traveled by the wood after the bullet emerges is 0.16 m.

The given parameters;

  • <em>mass of the bullet, m = 23 g = 0.023 g</em>
  • <em>speed of the bullet, u = 230 m/s</em>
  • <em>mass of the wood, m = 2 kg</em>
  • <em>final speed of the bullet, v = 170 m/s</em>
  • <em>coefficient of friction, μ = 0.15</em>

The final velocity of the wood after the bullet hits is calculated as follows;

m_1u_1 + m_2 u_2 = m_1v_1 + m_2v_2\\\\0.023(230) + 2(0) = 0.023(170) + 2v_2\\\\5.29 = 3.91 + 2v_2\\\\2v_2 = 1.38\\\\v_2 = \frac{1.38}{2} = 0.69 \ m/s

The acceleration of the wood is calculated as follows;

\mu = \frac{a}{g} \\\\a = \mu g\\\\a = 0.15 \times 9.8\\\\a = 1.47 \ m/s^2

The distance traveled by the wood after the bullet emerges is calculated as follows;

v^2 = v_0^2 + 2as\\\\v^2 = 0 + 2as\\\\v^2 = 2as\\\\s = \frac{v^2}{2a} \\\\s = \frac{(0.69)^2}{2(1.47)} \\\\s = 0.16 \ m

Thus, the distance traveled by the wood after the bullet emerges is 0.16 m.

Learn more here:brainly.com/question/15244782

7 0
3 years ago
At what point in its motion is the KE of a pendulum bob a maximum? 1. The KE does not change. 2. at the lowest point 3. at the h
Andrew [12]

Answer:

2. at the lowest point

Explanation:

The motion of the pendulum is a continuous conversion between kinetic energy (KE) and gravitational potential energy (GPE). This is because the mechanical energy of the pendulum, which is sum of KE and GPE, is constant:

E = KE + GPE = const.

Therefore, when KE is maximum, GPE is minimum, and viceversa.

So, the point of the motion where the KE is maximum is where the GPE is minimum: and since the GPE is directly proportional to the heigth of the bob:

GPE=mgh

we see that GPE is minimum when the bob is at the lowest point,so the correct answer is

2. at the lowest point

3 0
4 years ago
IIIIIIIIII neeeeeed helppppp again?
Juliette [100K]

Answer:

The Principle of Progression

(I searched it up since I never learned this)

Explanation:

The principle of progression states that a person should start slowly and increase exercise gradually. Since Mandy is just getting started on her exercise routine, she should begin with a few workouts over a large span of time, then work her way up so she can do more workouts in a shorter span of time.

7 0
3 years ago
Technician A says that side post terminals need to be removed to inspect them for corrosion. Technician B says that side post te
zlopas [31]

Answer: C

Explanation: Side post terminals need to be removed to inspect them for corrosion.

Over tightening the terminal bolt can damage side post terminals.

The battery terminals and cable ends can corrode especially when the battery or car is not used for a long period of time. Corrosion limits a battery's lifespan and so should be prevented. To inspect the areas where corrosion occur on a side-post battery, you need to remove the terminals.

Also, it is true that over tightening the terminal bolt can damage the side post terminals. The covering on the battery can become twisted, and make the seals on the terminals leak.

4 0
3 years ago
Other questions:
  • A curve has a radius of 50 meters and is banked 5 degrees. The road is covered with ice and is frictionless. What is the maximum
    12·1 answer
  • A block of mass m slides with a speed vo on a frictionless surface and collides with another mass M which is initially at rest.
    11·1 answer
  • What type of hybridization is exhibited by the nitrogen atom in the following substance pairs are present on the nitrogen?: and
    13·1 answer
  • Which of the following is a common technique advertisers use to mislead consumers into using "fad diets" to achieve optimal heal
    10·2 answers
  • Which phrase best describes sir isaac newton's contributions to modern science and therefore to the industrial revolution?
    14·1 answer
  • Consider n equal positively charged particles each of magnitude Q/n placed symmetrically around a circle of radius a. Calculate
    8·1 answer
  • A golf ball is struck with a velocity of 80 ft/s as shown. Determine the speed at which it strikes the ground at b and the time
    12·2 answers
  • What is the function of eye lens of the human eye<br>​
    15·1 answer
  • Which combination of vectors would form the resultant vector 6.5 m 18° N of E when added together?
    6·1 answer
  • Build a second circuit with a battery and a light bulb but this time add a switch. Your circuit might look something like the on
    9·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!