All categories

3 years ago

Which of these is the coarsest grit abrasive that may be used on aluminum?

Engineering

2 answers:

natali 33 [55]3 years ago

5 0

Answer:

80grit

Explanation:

80 grit is coarsest grit that may be used on aluminum

The lowest grit sizes range from 40 to 60. From the given options 80 grit is practically available grit.

What is a sandpaper used for?

They are essentially used for surface preparation. Sandpaper is produced in a range of grit sizes and is used to remove material from surfaces, either to make them smoother (for example, in painting and wood finishing), to remove a layer of material (such as old paint), or sometimes to make the surface rougher (for example, as a preparation for gluing).

Solnce55 [7]3 years ago

5 0

Answer 80 grit

Explanation: I got this question and I got it correct

You might be interested in

Storm sewer backup causes your basement to flood at the steady rate of 1 in. of depth per hour. The basement floor area is 2600

Wittaler [7]

Answer:

attached below

Explanation:

4 0

3 years ago

Determine the pressure difference in N/m2,between two points 800m apart in horizontal pipe-line,150 mm diameter, discharging wat

zlopas [31]

Answer: $10.631\times 10^3\ N/m^2$

Explanation:

Given

Discharge is $Q=12.5\ L$

Diameter of pipe $d=150\ mm$

Distance between two ends of pipe $L=800\ m$

friction factor $f=0.008$

Average velocity is given by

$\Rightarrow v_{avg}=\dfrac{12.5\times 10^{-3}}{\frac{\pi }{4}(0.15)^2}\\\\\Rightarrow v_{avg}=\dfrac{15.9134\times 10^{-3}}{2.25\times 10^{-2}}\\\\\Rightarrow v_{avg}=7.07\times 10^{-1}\\\Rightarrow v_{avg}=0.707\ m/s$

Pressure difference is given by

$\Rightarrow \Delta P=f\ \dfrac{L}{d}\dfrac{\rho v_{avg}^2}{2}\\\\\Rightarrow \Delta P=0.008\times \dfrac{800}{0.15}\times \dfrac{997\times (0.707)^2}{2}\\\\\Rightarrow \Delta P=10,631.45\ N/m^2\\\Rightarrow \Delta P=10.631\ kPa$

8 0

2 years ago

Type the correct answer in the box. Spell all words correctly.

Otrada [13]

Answer:

solar engineering field

5 0

3 years ago

Read 2 more answers

technician a says that dirt bypassing the filter on many common rail injectors can cause an injector to stick open and continuou

NNADVOKAT [17]

Technician a is correct because he says that Many common rail injectors filters can be bypassed by dirt, which can lead to an injector sticking open and continuously fueling a cylinder.

Coalescence is used to separate the water and fuel. To the fuel injector cleaning kit, fasten your air compressor. Diesel engines run at compression ratios that are greater than those of gasoline engines. greater ratio compared to gasoline engines. increased thermal expansion as a result. more fuel energy that is transformed into usable power. The great benefit of using a dry cylinder sleeve is that by quickly installing new sleeves, the cylinder block can be quickly restored to its original specifications. Vacuum drying can be used to get rid of small amounts of water. A nozzle is used to spray the fuel into the vacuum chamber of engines. Air and unsolved free water are taken out of the oil. The fuel is evenly dispersed, which facilitates efficient drying.

Learn more about injectors here:

brainly.com/question/27969202

#SPJ4

3 0

11 months ago

The purpose of pasteurizing milk is to A. Kill pathogens B. Break down milk fat C. Add vitamins and minerals D. Prevent spoilage

motikmotik

Answer: A Kill pathogens

7 0

2 years ago