1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
lara31 [8.8K]
3 years ago
10

Which option explains why Tyler is impressed in the following scenario?

Engineering
2 answers:
Art [367]3 years ago
8 0

Answer:

Its B).  The efficiency rating of the dishwasher was significantly improved, meaning it would save him money and be more eco-friendly.

Explanation:

On EDG

tamaranim1 [39]3 years ago
8 0

Answer:

It's B) i just did it in edg

Explanation:

You might be interested in
10. To cut 1/4" (6 mm) thick mild steel at a rate of 40 inches per minute, the current would be set to
pishuonlain [190]

Answer: Idk but try downloading more apps it’s a lot easier to have more than one

Explanation:

5 0
3 years ago
What are the most used electronic tools for electronic works?​
Zanzabum

Answer:

  • Needle-nose pliers.
  • Hemostats.
  • A spool of 30-gauge wire.
  • A spool of solder wick.
  • A spool of solder.
  • A loupe.
  • Three sets of tweezer

6 0
3 years ago
Which of the following is a advantage of a chain and sprocket over a pulley and belt system?
Tatiana [17]

Answer:

A) Cost

Explanation:

Chain drives have low maintenance cost.

3 0
3 years ago
Applications of fleming hand rule
Eva8 [605]

Answer:

Fleming hand rule represents the direction of current in a generator's windings and induced current as a conductor is attached to a circuit such that it moves in a magnetic field.

Explanation:

Fleming hand rule represents the direction of current in a generator's windings and induced current as a conductor is attached to a circuit such that it moves in a magnetic field.

Fleming hand rule is used in the case of electric motors and electric generators.

Fleming hand rule is used to determine the following:

1. Direction of torque

2. Angular velocity

3. Angular acceleration

4 0
3 years ago
Why does the compression-refrigeration cycle have a high-pressure side and a low-pressure side?
Cloud [144]

Answer: D

Explanation:

8 0
2 years ago
Other questions:
  • What is the entropy of a closed system in which 25 distinguishable grains of sand are distributed among 1000 distinguishable equ
    5·2 answers
  • Which of the following waste characteristic is considered to be hazardous:
    15·1 answer
  • Might give brainliest
    8·1 answer
  • Air enters a counterflow heat exchanger operating at steady state at 27 C, 0.3 MPa and exits at 12 C. Refrigerant 134a enters at
    5·1 answer
  • Which of these are factors of 121?
    13·2 answers
  • One reason the shuttle turns on its back after liftoff is to give the pilot a view of the horizon. Why might this be useful?
    6·2 answers
  • Technician A says that the low level brake fluid switch on a master cylinder will turn on the brake warning light when the syste
    9·1 answer
  • Hi I'm trying to build a desk that moves up and down electrically but i need help
    9·1 answer
  • During delivery of a 2023 ariya equipped with propilot assist 2. 0, what should you point out to your customers about the turn s
    12·1 answer
  • What’s the answer to this I don’t understand
    14·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!