1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
vampirchik [111]
3 years ago
11

A PLL is set up so that its VCO free-runs at 8.9 MHz. The VCO does not change frequency unless its input is within plus or minus

75 kHz of 8.9 MHz. After it does lock, the input frequency can be adjusted within plus or minus 120 kHz of 8.9 MHz without having the PLL start to free-run again. The tracking range of the PLL is:_________.
a) 75 kHz.
b) 120 kHz.
c) 150 kHz.
d) 240 kHz.
Engineering
1 answer:
pickupchik [31]3 years ago
5 0
It’s A 75khz because it’s plus or minus so if u add it would be too much
You might be interested in
3. When starting an automatic transmission
Alexxandr [17]

Answer:

It should be in Park or Neutral.

Explanation:

4 0
3 years ago
5) Calculate the LMC wal thickness of a pipe and tubing with OD as 35 + .05 and ID as 25 + .05 A) 4.95 B) 5.05 C) 10 D) 15.025
padilas [110]

Answer:

B) 5.05

Explanation:

The wall thickness of a pipe is the difference between the diameter of outer wall and the diameter of inner wall divided by 2. It is given by:

Thickness of pipe = (Outer wall diameter - Inner wall diameter) / 2

Given that:

Inner diameter = ID = 25 ± 0.05, Outer diameter = OD = 35 ± 0.05

Maximum outer diameter = 35 + 0.05 = 35.05

Minimum inner diameter = 25 - 0.05 = 24.95

Thickness of pipe = (maximum outer wall diameter - minimum inner wall diameter) / 2 = (35.05 - 24.95) / 2 = 5.05

or

Thickness = (35 - 25) / 2 + 0.05 = 10/2 + 0.05 = 5 + 0.05 = 5.05

Therefore the LMC wall thickness is 5.05

6 0
3 years ago
Read 2 more answers
The welding method that requires the operator to observe and only make corrections is
SVEN [57.7K]
Automatic manual semiautomatic
3 0
3 years ago
Read 2 more answers
A geothermal heat pump absorbs 15 KJ/s of heat from the Earth 15 m below a house. This heat pump uses a 7.45 kJ/s compressor.
Anna007 [38]

Answer:

COP of the heat pump is 3.013

OP of the cycle is  1.124

Explanation:

W = Q₂ - Q₁

Given

a)

Q₂ = Q₁ + W

     = 15 + 7.45

     = 22.45 kw

COP = Q₂ / W = 22.45 / 7.45 = 3.013

b)

Q₂ = 15 x 1.055 = 15.825 kw

therefore,

Q₁ = Q₂ - W

Q₁ = 15.825 - 7.45 = 8.375

∴ COP = Q₁ / W = 8.375 / 7.45 = 1.124

4 0
3 years ago
Read 2 more answers
Best use for a suspension bridge
babunello [35]

Answer:

over a rive or fast moving water or canyon

Explanation: you would use a suspension bridge in an area where you can't put supports down.

4 0
3 years ago
Other questions:
  • (1) 1. (15 points/ 3 points each) (a) Draw the binary search tree that is created if the following numbers are inserted in the t
    9·1 answer
  • 1. True or False: When two batteries are wired in Series the Volts go up and the Amp Hours stay the same. 2. True or False: When
    6·1 answer
  • Who can work on a fixed ladder that extends more than 24 feet?
    11·1 answer
  • Its an opinion!!!!
    8·1 answer
  • An electric power plant uses solid waste for fuel in the production of electricity. The cost Y in dollars per hour to produce el
    10·1 answer
  • A Barnes and Books is interested in purchasing a two-story building for a new
    5·1 answer
  • Estimate the uncertainty in a 22 m/sec air velocity measurement using a Pitot tube at 20C. Assume the atmospheric pressure is 1
    7·1 answer
  • What is the angular velocity (in rad/s) of a body rotating at N r.p.m.?
    13·1 answer
  • Q1. Basic calculation of the First law (2’) (a) Suppose that 150 kJ of work are used to compress a spring, and that 25 kJ of hea
    6·1 answer
  • Which rules of the road apply to people riding bicycles, under Illinois law? *
    9·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!