1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
stealth61 [152]
2 years ago
9

The volume of a steady-state crystallizer is 85,000 L, and the solids fraction in the unit and the exiting stream is 0.340; that

is, there are 0.340 kg of crystals per kg of slurry (the mixture of solid crystals and solution). The density of the solution is 1.15 g/mL and that of the crystals is 2.10 g/mL. The production rate of crystals from the crystallizer is 19.5 kg crystals/min.
Required:
Estimate the volumetric flow rate of slurry from the crystallizer and the drawdown time of the crystallizer (the time it would take to empty the crystallizer if the feed were discontinued).
Engineering
1 answer:
Stels [109]2 years ago
8 0

Answer:

https://www.chegg.com/homework-help/questions-and-answers/54-volume-steady-state-crystallizer-85-000-l-solids-fraction-unit-exiting-stream-035-035-k-q59132466

You might be interested in
A 3 ft x 2 ft block moves down a 15 degree inclined slope at a speed of V = 0.2 ft/s over a thin layer (h = 0.0125 ft) of oil wi
Ilia_Sergeevich [38]

Answer:

mg = 30.415 lbf

Explanation:

from figure body of size 3ft*2ft is tend to move down side

weight is divided into two component

vertical component =  mgcos15 and

horizontal component = mg sin15

considering horizontal component equal to shear force

mgsin15 = \tau A

mgsin15 =\mu \frac{dv}{dh} A

       mg =\frac{ \mu v A}{h*sin15}

             =\frac{8.2*10^{-2}*0.2*3*2}{0.0125*sin15}

        mg = 30.415 lbf

7 0
3 years ago
Structural engineers, designing an eighty-story office building, need to account for sway. They would most likely use a(n) ____
tia_tia [17]

Answer:

I would say a level

Explanation:

A level is used as a horizontal reference line, which will tell if the building is leaning to one side, or if its up right. I may be wrong but this is the closest thing I can think of for this question.

8 0
3 years ago
A.
nalin [4]

THE ANSWER IS B Beaycs i like BExplanation:

3 0
3 years ago
Wastewater flows into a once it is released into A floor drain
Phoenix [80]

Answer: C) Sump pit

Explanation:

Wastewater from the house is allowed to flow out of places such as the bathroom or the kitchen sink through a floor drain.

This floor drain is connected to a sump pit which is typically located at the lowest point in the house (lowest point in basement) so that water can flow into it easier.

When the wastewater is released from the floor drain, it will flow into the sump pit. This water is in turn removed from the pit by a sump pump.

8 0
3 years ago
A particular NMOS device has parameters VT N = 0.6 V, L = 0.8µm, tox = 200 Å, and µn = 600 cm2 /V–s. A drain current of ID = 1.2
NeTakaya

Answer:

W= 3.22 \mu m

Explanation:

the transistor In saturation drain current region is given by:

i_D}=K_a(V_{GS}-V_{IN})^2

Making K_a the subject of the formula; we have:

K_a=\frac {i_D} {(V_{GS} - V_{IN})^2}

where;

i_D = 1.2m

V_{GS}= 3.0V

V_{TN}  = 0.6 V

K_a=\frac {1.2m} {(3.0 - 0.6)^2}

K_a = 208.3 \mu A/V^2

Also;

k'_n}=\frac{\mu n (\frac{cm^2}{V-s} ) \epsilon _{ox}(\frac{F}{cm} ) }{t_{ox}(cm)}

where:

\mu n (\frac{cm^2}{V-s} ) = 600

\epsilon _{ox}=3.9*8.85*10^{-14}

{t_{ox}(cm)=200*10^{-8}

substituting our values; we have:

k'_n}=\frac{(600)(3.988.85*10^{-14})}{(200*10^{-8})}

k'_n}=103.545 \mu A/V^2

Finally, the width can be calculated by using the formula:

W= \frac{2LK_n}{k'n}

where;

L = 0.8 \mu m

W= \frac{2*0.8 \mu m *208.3 \mu}{103.545 \mu}

W= 3.22 \mu m

4 0
4 years ago
Other questions:
  • A heat pump with an ideal compressor operates between 0.2 MPa and 1 MPa. Refrigerant R134a flows through the system at a rate of
    15·1 answer
  • Problem 1 A coil measures ???? ???????? ⁄ meter in length with 500 turns of ???? ???? ⁄ inch diameter, and has a metallic core w
    13·1 answer
  • Consider a large plane wall of thickness L = 0.3 m, thermal conductivity k = 2.5 W/m · °C, and surface area A =12 m2. The left s
    6·1 answer
  • Explain why you chose the final design of your prototype and how it solved the identified need
    9·1 answer
  • Multiple Choice
    7·2 answers
  • What Advantage does a voltmeter have over a noncontact voltage indicator when testing for voltage
    15·1 answer
  • What is the horsepower of a 302 engine
    10·2 answers
  • Beyond providing a visual representation of an object for the creator, what are the advantages of using CAD software to create 3
    14·1 answer
  • Bebe receives a letter from the FBI stating that she is wanted for a crime. The letter says she must send her Social Security nu
    11·1 answer
  • Describe the refrigeration cycle & how it transfers heat, including all the components & lines. be sure to discuss why t
    9·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!