What is polarized electrical receptacle used for

What are the two most important things to remember when at the end of your interview?

Cloud [144]

<h3>Answer:</h3><h3><em>1. Ask questions</em></h3><h3><em>2. Thank the interviewer for their time </em></h3><h3>Explanation:</h3>

1<em>. When the interviewer asked if you have any questions at the end of the interview don't say no. You should always say yes your interviewer is expecting you to ask a few good questions before ending the interview. </em>

<em>2. Always thank the interviewer for their time and effort to interview you. This would look very good for you and its a nice way to help wrap up the interview. </em>

5 0

4 years ago

What is engine knock? What cause the engine knock problem?

antiseptic1488 [7]

Answer:

When the uneven burning of the fuel takes place due to the incorrect air/fuel mixture inside the engine cylinder, a knocking sound is observed. This is called as the engine knocking.

Explanation:

When the uneven burning of the fuel takes place due to the incorrect air/fuel mixture inside the engine cylinder, a knocking sound is observed. This is called as the engine knocking.

The engine knock problem can be caused due to the following reason

a) When the octane rating of the fuel used is low.

b) The deposition of the carbon around the cylinder walls takes place.

c) The spark plug used in the vehicle is not correct.

3 0

3 years ago

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 450°C, and 80 m/s, and the exit

8090 [49]

Answer:

a) The change in Kinetic energy, KE = -1.95 kJ

b) Power output, W = 10221.72 kW

c) Turbine inlet area, $A_1 = 0.0044 m^2$

Explanation:

a) Change in Kinetic Energy

For an adiabatic steady state flow of steam:

$KE = \frac{V_2^2 - V_1^2}{2} \\$ .........(1)

Where Inlet velocity, V₁ = 80 m/s

Outlet velocity, V₂ = 50 m/s

Substitute these values into equation (1)

$KE = \frac{50^2 - 80^2}{2} \\$

KE = -1950 m²/s²

To convert this to kJ/kg, divide by 1000

KE = -1950/1000

KE = -1.95 kJ/kg

b) The power output, w

The equation below is used to represent a steady state flow.

$q - w = h_2 - h_1 + KE + g(z_2 - z_1)$

For an adiabatic process, the rate of heat transfer, q = 0

z₂ = z₁

The equation thus reduces to :

w = h₁ - h₂ - KE...........(2)

Where Power output, $W = \dot{m}w$ ..........(3)

Mass flow rate, $\dot{m} = 12 kg/s$

To get the specific enthalpy at the inlet, h₁

At P₁ = 10 MPa, T₁ = 450°C,

h₁ = 3242.4 kJ/kg,

Specific volume, v₁ = 0.029782 m³/kg

At P₂ = 10 kPa, $h_f = 191.81 kJ/kg, h_{fg} = 2392.1 kJ/kg$ , x₂ = 0.92

specific enthalpy at the outlet, h₂ = $h_1 + x_2 h_{fg}$

h₂ = 3242.4 + 0.92(2392.1)

h₂ = 2392.54 kJ/kg

Substitute these values into equation (2)

w = 3242.4 - 2392.54 - (-1.95)

w = 851.81 kJ/kg

To get the power output, put the value of w into equation (3)

W = 12 * 851.81

W = 10221.72 kW

c) The turbine inlet area

$A_1V_1 = \dot{m}v_1\\\\A_1 * 80 = 12 * 0.029782\\\\80A_1 = 0.357\\\\A_1 = 0.357/80\\\\A_1 = 0.0044 m^2$

3 0

4 years ago

Consider a 2-shell-passes and 8-tube-passes shell-and-tube heat exchanger. What is the primary reason for using many tube passes

Maru [420]

Answer:

See explanation

Explanation:

Solution:-

- The shell and tube heat exchanger are designated by the order of tube and shell passes.

- A single tube pass: The fluid enters from inlet, exchange of heat, the fluid exits.

- A multiple tube pass: The fluid enters from inlet, exchange of heat, U bend of the fluid, exchange of heat, .... ( nth order of pass ), and then exits.

- By increasing the number of passes we have increased the "retention time" of a specific volume of tube fluid; hence, providing sufficient time for the fluid to exchange heat with the shell fluid.

- By making more U-turns we are allowing greater length for the fluid flow to develop with " constriction and turns " into turbulence. This turbulence usually at the final passes allows mixing of fluid and increases the heat transfer coefficient by:

U ∝ v^( 0.8 ) .... ( turbulence )

- The higher the velocity of the fluids the greater the heat transfer coefficient. The increase in the heat transfer coefficient will allow less heat energy carried by either of the fluids to be wasted ; hence, reduced losses.

Thereby, increases the thermal efficiency of the heat exchanger ( higher NTU units ).

5 0

3 years ago

The process _______ boosted the production of fertilizers and strengthened the agriculture industry.

ANTONII [103]

Answer:

Process of Green Revolution

Explanation:

Green Revolution is a process which started its initiatives between the 1950s and 1960s, a technological research process, that increase agricultural productions through various systematic approach, which are different from the traditional methods. These technological approach includes:

1. Utilization of new varieties with a high yield potential, in addition with adequate water supply, pesticides and fertilizers.

2. New methods of cultivation and mechanization

Hence, the process of Green Revolution boosted production of fertilizers and strengthen the agriculture industry as a whole.

6 0

3 years ago