All categories

4 years ago

What is a good safety precaution when fueling your boat?

Engineering

1 answer:

DaniilM [7]4 years ago

8 0

Answer:

Explanation:

You must :

Turn off your phone
Turn off any electronic device
avoid smoking
use good quality fuel
Turn off the engine

You might be interested in

Why is concrete on its own not a good material to use

Inga [223]

Answer:

It has poor tensile strength despite having high compressive strength

Explanation:

Concrete exhibits high compressive strength when used. However, it has very low compressive strength. This is the reason why concrete is normally combined with steel to make a composite building material called reinforced concrete. The steel reinforces concrete hence increasing the tensile strength in RC buildings. The end composite is durable and fireproof. Generally, the main reason why concrete is not use on its own is due to its poor tensile strength.

7 0

3 years ago

If you are interested only in the temperature range of 20° to 40°C and the ADC has a 0 to 3V input range, design a signal condit

mario62 [17]

Explanation:

Temperature range → 0 to 80'c

respective voltage output → 0.2v to 0.5v

required temperature range 20'c to 40'c

Where T = 20'c respective voltage

$\begin{aligned}v_{20} &=0.2+\frac{0.5-0.8}{80} \times 20 \\&=0.2+\frac{0.3}{80} \times 20 \\V_{20} &=0.275 v\end{aligned}$

$\begin{aligned}\text { when } T=40^{\circ} C & \text { . } \\v_{40} &=0.2+\frac{0.5-0.2}{80} \times 40 \\&=0.35 V\end{aligned}$

Therefore, Sensor output changes from 0.275v to 0.35volts for the ADC the required i/p should cover the dynamic range of ADC (ie - 0v to 3v)

so we have to design a circuit which transfers input voltage 0.275volts - 0.35v to 0 - 3v

Therefore, the formula for the circuit will be

$\begin{array}{l}v_{0}=\left(v_{i n}-0.275\right) G \\\sigma=\ldots \frac{3-0}{0.35-0.275}=3 / 0.075=40 \\v_{0}=\left(v_{i n}-0.275\right) 40\end{array}$

The simplest circuit will be a op-amp

NOTE: Refer the figure attached

Vs is sensor output

Vr is the reference volt, Vr = 0.275v

$\begin{aligned}v_{0}=& v_{s}-v_{v}\left(1+\frac{R_{2}}{R_{1}}\right) \\\Rightarrow & \frac{1+\frac{R_{2}}{R_{1}}}{2}=40 \\& \frac{R_{2}}{R_{1}}=39 \quad \Rightarrow\end{aligned}$

choose R2, R1 such that it will maintain required ratio

The output Vo can be connected to voltage buffer if you required better isolation.

3 0

3 years ago

The increasing interconnections of peoples and countries around the world is known as ________.

Irina18 [472]

I think it’s rationalization.
Hope this helps

4 0

4 years ago

Read 2 more answers

Hãy trình bày các bộ phận chính trong một bộ điều khiển điện tử (ECU) dùng trên ô tô. Cho biết công dụng của từng thành phần.

mestny [16]

Answer:

sorry but I can't understand this Language.

Explanation:

unable to answer sorry

5 0

3 years ago

A heat pump operates on a vapor-compression refrigeration cycle with R-134a as the working fluid. The refrigerant enters the com

Rudiy27

Answer:

Hello your question has some missing information below are the missing information

The refrigerant enters the compressor as saturated vapor at 140kPa Determine The coefficient of performance of this heat pump

answer : 2.49

Explanation:

For vapor-compression refrigeration cycle

P1 = P4 ; P1 = 140 kPa

P2( pressure at inlet ) = P3 ( pressure at outlet ) ; P2 = 800 kPa

<u>From pressure table of R 134a refrigerant</u>

h1 ( enthalpy of saturated vapor at 140kPa ) = 239.16 kJ/kg

h2 ( enthalpy of saturated liquid at P2 = 800 kPa and t = 60°C )

= 296.8kJ/kg

h3 ( enthalpy of saturated liquid at P3 = 800 kPa ) = 95.47 kJ/kg

also h4 = 95.47 kJ/kg

To determine the coefficient of performance

Cop = ( h1 - h4 ) / ( h2 - h1 )

∴ Cop = 2.49

3 0

3 years ago