All categories

3 years ago

Help me in economics

Engineering

1 answer:

soldi70 [24.7K]3 years ago

5 0

Answer:

Actualmente estoy trabajando en una pregunta diferente en este momento.

Explanation:

Actualmente estoy trabajando en una pregunta diferente en este momento.

You might be interested in

For a body moving with simple harmonic motion state the equations to represent: i) Velocity ii) Acceleration iii) Periodic Time

max2010maxim [7]

Answer with Explanation:

The general equation of simple harmonic motion is

$x(t)=Asin(\omega t+\phi)$

where,

A is the amplitude of motion

$\omega$ is the angular frequency of the motion

$\phi$ is known as initial phase

part 1)

Now by definition of velocity we have

$v=\frac{dx}{dt}\\\\\therefore v(t)=\frac{d}{dt}(Asin(\omega t+\phi )\\\\v(t)=A\omega cos(\omega t+\phi )$

part 2)

Now by definition of acceleration we have

$a=\frac{dv}{dt}\\\\\therefore a(t)=\frac{d}{dt}(A\omega cos(\omega t+\phi )\\\\a(t)=-A\omega ^{2}sin(\omega t+\phi )$

part 3)

The angular frequency is related to Time period 'T' as $T =\frac{2\pi }{\omega }$

where

$\omega$ is the angular frequency of the motion of the particle.

Part 4) The acceleration and velocities are plotted below

since the maximum value that the sin(x) and cos(x) can achieve in their respective domains equals 1 thus the maximum value of acceleration and velocity is $A\omega ^{2}$ and $A\omega$ respectively.

4 0

3 years ago

Hello Averyone Subs Chanel Me please "RezaDarmawangsa "<br>Thanks !!

Yanka [14]

Answer:

what kind of content? I need to know

4 0

3 years ago

Consider a 2-shell-passes and 8-tube-passes shell-and-tube heat exchanger. What is the primary reason for using many tube passes

Maru [420]

Answer:

See explanation

Explanation:

Solution:-

- The shell and tube heat exchanger are designated by the order of tube and shell passes.

- A single tube pass: The fluid enters from inlet, exchange of heat, the fluid exits.

- A multiple tube pass: The fluid enters from inlet, exchange of heat, U bend of the fluid, exchange of heat, .... ( nth order of pass ), and then exits.

- By increasing the number of passes we have increased the "retention time" of a specific volume of tube fluid; hence, providing sufficient time for the fluid to exchange heat with the shell fluid.

- By making more U-turns we are allowing greater length for the fluid flow to develop with " constriction and turns " into turbulence. This turbulence usually at the final passes allows mixing of fluid and increases the heat transfer coefficient by:

U ∝ v^( 0.8 ) .... ( turbulence )

- The higher the velocity of the fluids the greater the heat transfer coefficient. The increase in the heat transfer coefficient will allow less heat energy carried by either of the fluids to be wasted ; hence, reduced losses.

Thereby, increases the thermal efficiency of the heat exchanger ( higher NTU units ).

5 0

3 years ago

name the three exposure techniques in photolithography. what are the alternatives to photolithography in ic processing?

zhenek [66]

The three exposure techniques in photolithography are:

Contact
Proximity
Projection

Alternatives to photolithography in IC processing include;

X-ray
UV
Ion, and
Electron lithography

<h3>What is Photolithography?</h3>

Photolithography is a term in integrated circuit development that describes the patterned films that are formed when a beam of light falls on a substance.

This phenomenon protects the surface of sensitive materials such as glass during some operations like etching. UV and X-rays can be used for this purpose.

Learn more about photolithography here:

brainly.com/question/13650094

#SPJ11

6 0

2 years ago

stimate the maximum efficiency of an automobile engine that has a compression ratio of 5:1.0. Assume the engine operates accordi

Fed [463]

Answer:

Efficiency based on Otto cycle.

Effotto = 47.47%

Explanation:

Efficiency based on Otto cycle.

effotto = 1 – (V2 / V1)^γ-1

effotto = 1 – (1 / 5)^1.4 - 1

effotto = 47.47%

5 0

3 years ago