Que os vizinhos diziam sempre aq lenhador? Responda com elementos do texto.

A customer got debited twice, how would you investigate and resolve this conflict on the customer side and on the company side?

eimsori [14]

Answer:

First, the question seems to assume that the debit is erroneous. Because, if it's intentional, then there is little need for an investigation.

So if there was an unintentional duplication of transaction, this would totally depend on what kind of debit it is. So to answer the question, we'll explore as many scenarios as possible.

Debit on a Bank Account (Business to Bank)

If it is a debit on the bank account, then the statement of account from the company side and the account activity(ies) leading up to the debits will reveal why there is a double debit. It is possible the transaction was entered twice. This can happen when there is a bad connection that creates a failed transaction message on the customer's end but still carries through with the payment instruction. In this case, the customer will think the debit or payment request didn't go through and proceed to repeat the same transaction.

Banks do execute debits on accounts for charges such as Bank Account Maintenance Charges, Credit card charges etc. Errors could also arise internally that led to the duplication of a debit instruction either due to a bug in the system.

So in this case, we'll need to access the customer's account internally whilst externally, the client will need to provide the message containing the alerts, date and time of debits etc. to help the banks further the investigation.

Business to Business

This could arise out of a "failed POS" transaction. Similar to the condition stated above, when there is a glitch with the network and the POS fails, it should print out a receipt that reads failed or declined.

This receipt will contain references to the transaction. This will aid the investigation of the debits to the account.

Explanation:

8 0

3 years ago

A stainless steel ball (=8055 kg/m3, Cp= 480 J/kgK) of diameter D =15 cm is removed from theoven at a uniform temperature of 3

aleksandrvk [35]

Answer:

i) 25.04 W/m^2 .k

ii) 23.82 minutes = 1429.2 secs

Explanation:

Given data:

Diameter of steel ball = 15 cm

uniform temperature = 350°C

p = 8055 kg/m^3

Cp = 480 J/kg.k

surface temp of ball drops to 250°C

average surface temperature = ( 350 + 250 ) / 2 = 300°C

i) Determine the average convection heat transfer coefficient during the cooling process

Note : Obtain the properties of air at 1 atm at average film temp of 30°C from the table " properties of air " contained in your textbook

average convection heat transfer coefficient = 25.04 W/m^2 .k

ii) Determine how long this process has taken

Time taken by the process = 23.82 minutes = 1429.2 seconds

Δt = Qtotal / Qavg = 683232 / 477.92 = 1429.59 secs

attached below is the detailed solution of the given question

3 0

3 years ago

What is vapier calliper

SIZIF [17.4K]

Answer:

A calliper is a device used to measure the dimensions of an object.

Many types of calipers permit reading out a measurement on a ruled scale, a dial, or a digital display. Some calipers can be as simple as a compass with inward or outward-facing points, but no scale.

I'm not sure what a "Vapier" Calliper is, but I assume it's about the same thing.

4 0

2 years ago

Which of the following has special properties that allow forces and pressure to be distributed evenly?

Thepotemich [5.8K]

Answer:

Fluids

Explanation:

Fluids has special properties that allow forces and pressure to be distributed evenly within them.

Fluids are gases and liquids whose intermolecular forces of attraction are generally weak or non-existence.
Therefore, when pressure is applied to them, it permeates evenly on all parts.
Their ability to tend to randomness makes liquids and gases very viable for distributing pressure.

7 0

3 years ago

A and B connect the gear box to the wheel assemblies of a tractor, and shaft C connects it to the engine. Shafts A and Blie in t

azamat

Answer:

The couples are not all on one axis or plane for that matter but if the A and B connector had to be specified it would go by the yz axis diagonal to the x axis with a magnitude of about 15. The direction of the axis would be pointed up to the second quadrant. Hope this was helpful

Explanation:

8 0

4 years ago

Que os vizinhos diziam sempre aq lenhador? Responda com elementos do texto.​

Que os vizinhos diziam sempre aq lenhador? Responda com elementos do texto.