All categories

3 years ago

Which line in the passage indicates the use of sensors?

Engineering

1 answer:

IrinaK [193]3 years ago

4 0

Answer:

B: It drills holes for electric sockets with the right amount of pressure

Explanation:

Pressure sensor.

You might be interested in

Solid Isomorphous alloys strength

Sphinxa [80]

Answer:

Explanation:

ℎ

3 0

3 years ago

The term _______________refers to the science of using fluids to perform work.

Alla [95]

The term is hydraulics.

5 0

3 years ago

Read 2 more answers

Water at a pressure of 3 bars enters a short horizontal convergent channel at 3.5 m/s. The upstream and downstream diameters of

earnstyle [38]

Answer:

The pressure reduces to 2.588 bars.

Explanation:

According to Bernoulli's theorem for ideal flow we have

$\frac{P}{\gamma _{w}}+\frac{V^{2}}{2g}+z=constant$

Since the losses are neglected thus applying this theorm between upper and lower porion we have

$\frac{P_{u}}{\gamma _{w}}+\frac{V-{u}^{2}}{2g}+z_{u}=\frac{P_{L}}{\gamma _{w}}+\frac{V{L}^{2}}{2g}+z_{L}$

Now by continuity equation we have

$A_{u}v_{u}=A_{L}v_{L}\\\\\therefore v_{L}=\frac{A_{u}}{A_{L}}\times v_{u}\\\\v_{L}=\frac{d^{2}_{u}}{d^{2}_{L}}\times v_{u}\\\\\therefore v_{L}=\frac{2500}{900}\times 3.5\\\\\therefore v_{L}=9.72m/s$

Applying the values in the Bernoulli's equation we get

$\frac{P_{L}}{\gamma _{w}}=\frac{300000}{\gamma _{w}}+\frac{3.5^{2}}{2g}-\frac{9.72^{2}}{2g}(\because z_{L}=z_{u})\\\\\frac{P_{L}}{\gamma _{w}}=26.38m\\\\\therefore P_{L}=258885.8Pa\\\\\therefore P_{L}=2.588bars$

6 0

4 years ago

For an Otto cycle, plot the cycle efficiency as a function of compression ratio from 4 to 16.

Elza [17]

Assumptions:

Steady state.
Air as working fluid.
Ideal gas.
Reversible process.
Ideal Otto Cycle.

Explanation:

Otto cycle is a thermodynamic cycle widely used in automobile engines, in which an amount of gas (air) experiences changes of pressure, temperature, volume, addition of heat, and removal of heat. The cycle is composed by (following the P-V diagram):

Intake <em>0-1</em>: the mass of working fluid is drawn into the piston at a constant pressure.

Adiabatic compression <em>1-2</em>: the mass of working fluid is compressed isentropically from State 1 to State 2 through compression ratio (r).

$r =\frac{V_1}{V_2}$

Ignition 2-3: the volume remains constant while heat is added to the mass of gas.
Expansion 3-4: the working fluid does work on the piston due to the high pressure within it, thus the working fluid reaches the maximum volume through the compression ratio.

$r = \frac{V_4}{V_3} = \frac{V_1}{V_2}$

Heat Rejection 4-1: heat is removed from the working fluid as the pressure drops instantaneously.
Exhaust 1-0: the working fluid is vented to the atmosphere.

If the system produces enough work, the automobile and its occupants will propel. On the other hand, the efficiency of the Otto Cycle is defined as follows:

$\eta = 1-(\frac{1}{r^{\gamma - 1} } )$