The formula for acceleration is a = F/m; Where: F = force; m = mass
Given: F = .6n; m = .4kg; a = ?
a = F/m
= .6/.4
= 1.5
Therefore, the acceleration of the plate is 1.5 m/s^2
The tension in the two chains T1 and T2 is 676.65 N and 542.53 N respectively.
<h3>Principle of moments</h3>
The Principle of Moments states that when a body is in equip, the sum of clockwise moment about a point is equal to the sum of anticlockwise moment about the same point.
The formula for calculating moment is given below:
- Moment = Force × perpendicular distance from the pivot
<h3>Calculating the tension in the chains</h3>
From the principle of moments:
Let tension in chain 1 be T1 and tension in chain 2 be T2.
T1 + T2 = 150 + 650 + 419
T1 + T2 =1219
Taking all distances from chain 1,
Sum of Moments = 0
419 × 0.5 + 150 × 0.85 + 650 × 0.9 = T2 × 1.7
T2 = 922/17
T2 = 542.35 N
Then, T1 = 1219 - 542.35
T1 = 676.65 N
Therefore, the tension in the two chains T1 and T2 is 676.65 N and 542.53 N respectively.
Learn more about tension and moments at: brainly.com/question/187404
brainly.com/question/14303536
Answer: a) 1 b) 61 W c) 61 W
Explanation:
a) The Power Factor (also known as cos φ), is defined by the difference in phase between current and voltage, in a RLC series circuit, and is expressed as follows:
cos φ = R / Z = R / 
In resonance, XL =XC, so the circuit behaves like it were purely resistive, so Z=R.
Replacing in the expression for power factor, we have:
cos φ = R/Z = R/R = 1
This means that in resonance, current and voltage are in phase each other.
b) The average power delivered by the source, in resonance, is simply the power dissipated at the resistance R, as follows:
Pavg = V² rms / R = V₀² / √2 / R = 61 W
c) If the circuit remains in resonance, the average power , which does not depends on frequency provided this condition remains, keeps the same, i.e. , 61 W.
Answer:
<em>B) 1.0 × 10^5 V</em>
Explanation:
<u>Electric Potential Due To Point Charges
</u>
The electric potential produced from a point charge Q at a distance r from the charge is
The total electric potential for a system of point charges is equal to the sum of their individual potentials. This is a scalar sum, so direction is not relevant.
We must compute the total electric potential in the center of the square. We need to know the distance from all the corners to the center. The diagonal of the square is
where a is the length of the side.
The distance from any corner to the center is half the diagonal, thus
The total potential is
Where V1 and V2 are produced by the +4\mu C charges and V3 and V4 are produced by the two opposite charges of 
. Since all the distances are equal, and the charges producing V3 and V4 are opposite, V3 and V4 cancel each other. We only need to compute V1 or V2, since they are equal, but they won't cancel.
The total potential is
85)
The bone structure from outside would be periosteum, cortical, cancellous then medulla. Periosteum is the area outside the bone that will supply nutrition into the outer part of the bone. Cortical is the layer where bone mineral deposition is intense. In this part, the bone is compact and hard. This is the part of the bone that has great strength.
Cancellous is part of the bone where it is not too hard but not too soft. Mineralization is not so dense like cortical layer. That makes this part looks spongy.
In the medulla, most part is made from connective tissue and blood vessels. This part is responsible for the bone vascularization, which means the supply of mineral to the outer part is coming from the medulla. Mineralization is not much in the medulla, makes it not strong. Medulla or marrow also makes blood cells.
86)
The region of the spine would be cervical(neck), thoracal(chest), lumbar(back), sacrum then coccyx. The vertebrae in the neck are smaller since it did not need much strength but need more mobility. Lower part on the thoracal and lumbar is bigger and have a bigger process that will further stabilize the vertebrae. Thoracal vertebrae have a part on their side where the ribs attached. Sacrum shape was a kinda weird because it needs to be able to connect with the pelvis to make buttock. Coccyx the tailbone look like just a small remnant and doesn't seem to have a function in human.
87)
Axis is the name of cervical 2nd vertebral which was located below the atlas, 1st cervical vertebrae. Both of them doesn't have spinal processes that were stabilizing the side of vertebrae Axis also has an odontoid peg which will make the joint with atlas more flexible.
This effect makes the neck can turn to side easily. It also makes neck more mobile vertically, make a nodding movement is possible.
88)
Thre kind of joints would be: Synarthrosis, amphiarthrosis, and diarthrosis.
In synarthrosis, the joint mostly made by fibrous so that it can move. The example of this joint would be suture in the skull. In children, the skull joint is not closed to permit the head to grow but in the adult, it is closed.
Amphiarthrosis joint permits a small movement. This included the intervertebral disc.
Diarthrosis permit a wide degree of movement. This joint is more complex because it has the synovial membrane. The complex structure makes the joints more durable to shock. This was vital because organ with this join used frequently. The example of this joints would be femur and pelvic(hip) joints. Joints in arm and leg mostly diarthrosis joint.
