The statement “Only the “Conclusion” section discusses whether the original hypothesis was supported, and both sections suggest further research”, best describes the difference between analysis and conclusion.
Answer: Option 4
<u>Explanation:
</u>
In research, we do experiments and derive the results. Then, those results were analyzed by us. In this analysis part, we compare our results with the related results published elsewhere. Also, we correlate the similarities and point out the differences between our analysis and other reported results.
In conclusion part, we have to check hypothesis or it supported. And, we summarise our analysis and figure out the further research need to be done on that to improvise our research. So, the final statement is the correct option which best describes the difference between analysis and conclusion.
We know that the number of moles HCl in 14.3mL of 0.1M HCl can be found by multiplying the volume (in L) by the concentration (in M).
(0.0143L HCl)x(0.1M HCl)=0.00143 moles HCl
Since HCl reacts with KOH in a one to one molar ratio (KOH+HCl⇒H₂O+KCl), the number of moles HCl used to neutralize KOH is the number of moles KOH. Therefore the 25mL solution had to contain 0.00143mol KOH.
To find the mass of KOH in the original mixture you have to divide the number of moles of KOH by the 0.025L to find the molarity of the KOH solution..
(0.00143mol KOH)/(0.025L)=0.0572M KOH
Since the morality does not change when you take some of the solution away, we know that the 250mL solution also had a molarity of 0.0572. That being said you can find the number of moles the mixture had by multiplying 0.0572M KOH by 0.250L to get the number of moles of KOH.
(0.0572M KOH)x(0.250L)=0.0143mol KOH
Now you can find the mass of the KOH by multiplying it by its molar mass of 56.1g/mol.
0.0143molx56.1g/mol=0.802g KOH
Finally you can calulate the percent KOH of the original mixture by dividing the mass of the KOH by 5g.
0.802g/5g=0.1604
the original mixture was 16% KOH
I hope this helps.
2.083 Liters of 6.0 M solution sulfuric acid is required. This solved using molecular calculations and Titration.
Solution: 
Moles of hydrogen gas = 
Then 12.5 moles of hydrogen will be obtained from Moles of Sulfuric acid = 12.5 mol
Molarity of the sulfuric acid solution = 6.0 M = 6 mol/ l
6M = 
where V is the volume needed
V = 2.083 l
<h3>
What is Titration?</h3>
- Titration, commonly referred to as titrimetry, is a typical quantitative chemical analysis method used in laboratories to ascertain the unidentified quantity of an analyte .
- Titration is frequently referred to as volumetric analysis because it relies heavily on volume measurements. The titrant or titrator is a reagent that is prepared as a standard solution.
- To determine concentration, a solution of the analyte or titrand reacts with a known concentration and volume of the titrant. The titration volume is the amount of titrant that has responded.
- Titrations come in a variety of forms with various protocols and objectives. Redox and acid-base titrations are the two most typical types of qualitative titrations.
To learn more about titration with the given link
brainly.com/question/2728613
#SPJ4
Answer:
357.475
Explanation:
First you need periodic table and you have to look for mass
Fe = 3 x 55.845 = 167.535
P = 2 x 30.97 = 61.94
o = 4 x 2 so 8 oxygen = 8 x 16 = 128
add all and you get 357.475
Answer:
Heating the system
Explanation:
According to the principle of Le Chatelier, for a system at equilibrium, a specific disturbance would make the equilibrium shift toward the direction which minimizes such a disturbance.
Since we wish to shift the equilibrium to the left, this means we wish to increase the concentration of products, as an excess in their concentration would make the products react and produce more reactants in order to lower the excess concentration of products.
Since heat is also a product, an increase in heat would shift the equilibrium toward the left, as this would consume the excess of heat by producing the reactants.
