Hey, it depends what you subscribed to, or what platform you are trying to unsubscribe from?
Answer:
Code is given below:
Explanation:
.data
str1: .space 20
str2: .space 20
msg1:.asciiz "Please enter string (max 20 characters): "
msg2: .asciiz "\n Please enter string (max 20 chars): "
msg3:.asciiz "\nSAME"
msg4:.asciiz "\nNOT SAME"
.text
.globl main
main:
li $v0,4 #loads msg1
la $a0,msg1
syscall
li $v0,8
la $a0,str1
addi $a1,$zero,20
syscall #got string to manipulate
li $v0,4 #loads msg2
la $a0,msg2
syscall
li $v0,8
la $a0,str2
addi $a1,$zero,20
syscall #got string
la $a0,str1 #pass address of str1
la $a1,str2 #pass address of str2
jal methodComp #call methodComp
beq $v0,$zero,ok #check result
li $v0,4
la $a0,msg4
syscall
j exit
ok:
li $v0,4
la $a0,msg3
syscall
exit:
li $v0,10
syscall
methodComp:
add $t0,$zero,$zero
add $t1,$zero,$a0
add $t2,$zero,$a1
loop:
lb $t3($t1) #load a byte from each string
lb $t4($t2)
beqz $t3,checkt2 #str1 end
beqz $t4,missmatch
slt $t5,$t3,$t4 #compare two bytes
bnez $t5,missmatch
addi $t1,$t1,1 #t1 points to the next byte of str1
addi $t2,$t2,1
j loop
missmatch:
addi $v0,$zero,1
j endfunction
checkt2:
bnez $t4,missmatch
add $v0,$zero,$zero
endfunction:
jr $ra
Answer:
Amperes WB =<em> </em>
Explanation:
Amperes will flow back to the negative terminal because both the positive terminal and negative terminal contain the equivalent amount of current that will flow and it works in the starter motor.
To learn more about it, refer
to brainly.com/question/6561461
#SPJ4
The weight of the specimen in SSD condition is 373.3 cc
<u>Explanation</u>:
a) Apparent specific gravity = 
Where,
A = mass of oven dried test sample in air = 1034 g
B = saturated surface test sample in air = 1048.9 g
C = apparent mass of saturated test sample in water = 975.6 g
apparent specific gravity =
= 
Apparent specific gravity = 2.88
b) Bulk specific gravity 
= 2.76
c) Bulk specific gravity (SSD):
= 2.80
d) Absorption% :
Absorption = 1.44 %
e) Bulk Volume :
= 
Answer:
The Poisson's Ratio of the bar is 0.247
Explanation:
The Poisson's ratio is got by using the formula
Lateral strain / longitudinal strain
Lateral strain = elongation / original width (since we are given the change in width as a result of compession)
Lateral strain = 0.15mm / 40 mm =0.00375
Please note that strain is a dimensionless quantity, hence it has no unit.
The Longitudinal strain is the ratio of the elongation to the original length in the longitudinal direction.
Longitudinal strain = 4.1 mm / 270 mm = 0.015185
Hence, the Poisson's ratio of the bar is 0.00375/0.015185 = 0.247
The Poisson's Ratio of the bar is 0.247
Please note also that this quantity also does not have a dimension
