1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Nikitich [7]
3 years ago
15

What is hot tear in casting? How can we avoid it?

Engineering
1 answer:
Anestetic [448]3 years ago
3 0

Answer:

Hot tear casting is the discontinuity or failures occurs during cooling or solidification phase in casting process. It is also known as hot crack

Explanation:

In case when the casting is of weak metal, when it is hot and casted, during the process residual stresses cause failures or discontinuity in casting as it cools resulting in hot tears i,e., material casted is partly liquid and partly solid.

Preventive measures:

  • Ensure proper mold design
  • A no. of gates should be used to even out temperature gradient.
  • Over heated mold parts should not be used
  • Proper choice of mold materials
You might be interested in
A two-phase mixture of water and steam with a quality of 0.63 and T = 300F expands isothermally until only saturated vapor rema
VMariaS [17]

Answer:

Explanation:

Hello!

To solve this problem you must follow the following steps, which are fully registered in the attached image.

1. Draw the complete outline of the problem.

2. Through laboratory tests, thermodynamic tables were developed, these allow to know all the thermodynamic properties of a substance (entropy, enthalpy, pressure, specific volume, internal energy etc ..)

through prior knowledge of two other properties.

3. Use temodynamic tables to find the density of water in state 1, by means of temperature and quality, with this value and volume we can find the mass.

3. Use thermodynamic tables to find the internal energy in state 1 and two using temperature and quality.

4. uses the first law of thermodynamics that states that the energy in a system is always conserved, replaces the previously found values ​​and finds the work done.

5. draw the pV diagram using the 300F isothermal line

5 0
3 years ago
Please read and answer each question carefully.
Klio2033 [76]

the answer is (c)

After the vehicle is involved in a car accident or fire

5 0
4 years ago
What did August Comte contribute to sociology including positivism
Travka [436]

Answer:

Auguste Comte was the first to develop the concept of "sociology." He defined sociology as a positive science. Positivism is the search for "invariant laws of the natural and social world." Comte identified three basic methods for discovering these invariant laws, observation, experimentation, and comparison.

Explanation:

I hope it's help u :)

4 0
3 years ago
A video inspection snake is use
LekaFEV [45]

Answer:

very good thx

Explanation:

5 0
3 years ago
compressors, the gas is often cooled while being compressed to reduce the power consumed by the compressor. explain how cooling
ASHA 777 [7]

The amount of work done by steady flow devices varies with the particular gas volume. The kinetic energy of gas particles decreases during cooling.

When the gas is subjected to intermediate cooling during compression, the gas specific volume is reduced, which lowers the compressor's power consumption. Compression is less adiabatic and more isothermal because the compressed gas must be cooled between stages since compression produces heat. The system's thermodynamic cycle's cold sink temperature is lowered by cooling the compressor coils. By increasing the temperature difference between the heat source and the cold sink, this improves efficiency.

Learn more about thermodynamics here-

brainly.com/question/1368306

#SPJ4

8 0
2 years ago
Other questions:
  • ): drivers must slow down from 60 to 40 mi/hr to negotiate a severe curve. A warning sign is visible for a distance of 120 ft. H
    7·1 answer
  • A hydrogen-filled balloon to be used in high altitude atmosphere studies will eventually be 100 ft in diameter. At 150,000 ft, t
    7·1 answer
  • What is the base unit in standard measurement
    13·2 answers
  • When trying to solve a frame problem it will typically be necessary to draw many free body diagrams. a)-True b)-False
    6·1 answer
  • Describe the make-up of an internal combustion engine.<br> Pls answer quickly.
    5·1 answer
  • Materials to be used to build a watch tower​
    9·1 answer
  • Why is there an Engineering Process?
    15·2 answers
  • Can someone please help me?
    11·2 answers
  • Question 3
    14·1 answer
  • 8. What are used by the project architect to depict different building systems and to show how they correlate to one anothe
    14·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!