Answer:
5.2x10^-25
Explanation:
Time=(1.56x 10^-16)÷(3x10^8)
Answer:
<u>36 m</u>
Explanation:
We can consider this to be an AP.
Then,
<u>Subtract a₇ from a₉.</u>
- a + 8d - a + 6d = 24 - 20
- 2d = 4
- d = 2
<u>Finding a₁₅</u>
- a₁₅ = a + 14d
- a₁₅ = 8 + 14(2)
- a₁₅ = 8 + 28
- a₁₅ = <u>36 m</u>
Answer:
a = -8.912 m/s²
Explanation:
Given,
The initial velocity of the car, u = 28 m/s
The final velocity of the car, v = 0
The distance traveled by car, d = 88 m
The velocity displacement relation is given by the formula
v = d/t
∴ t = d/v
Substituting in the above values in the given equation
t = 88/28
= 3.142 s
The acceleration is given by the formula
a = (v-u)/t
= (0 - 28)/3.142
= -8.912 m/s²
The negative sign is that the car is decelerating.
Hence, acceleration a = -8.912 m/s²
Answer:
Two marbles are launched at t = 0 in the experiment illustrated in the figure below. Marble 1 is launched horizontally with a speed of 4.20 m/s from a height h = 0.950 m. Marble 2 is launched from ground level with a speed of 5.94 m/s at an angle above the horizontal. (a) Where would the marbles collide in the absence of gravity? Give the x and y coordinates of the collision point. (b) Where do the marbles collide given that gravity produces a downward acceleration of g = 9.81 m/s2? Give the x and y coordinates.
Explanation:
i want the answer i don't know
Answer:
Explanation:
Well you have the voltages right, and that is no trivial matter. Each one of the resistors in a parallel circuit sees the same input voltages (in this case 6).
Now I think it would be a good idea to fill in the the resistance column.
R1 = 3 ohms
R2 = 6 ohms
R3 = 2 ohms
The total resistance can be calculated in two ways. I'll get around to doing both of them but I'll do the conventional way first. One hint: the total resistance must be smaller than the smallest resistor. Read that sentence over a couple of times. What it means is that it must be less than 2 ohms in a parallel circuit.
1/r1 + 1/r2 + 1/r3 = 1/rt
1/3 + 1/6 + 1/2 = 1/rt
Change all the denominators to 6ths.
2/6 + 1/6 + 3/6 = 1/rt
(2 + 1 + 3)/6 = 6/6 = 1
rt = 1
====================
So the current I is V/R
V = 6
R = 1
Current = V/R = 6/1 = 6 amps.
====================
The current in each resistor is
I1 = V / R1
I1 = 6/3 = 2 amps
I2 = V/R2
I2 = 6/6 = 1 amp
I3 = 6/2 = 3 amps
The total is I1 + I2 + I3 = 2 + 1 + 3 = 6 amps.
======================
Remember I said there was 2 ways of figuring out the total resistance. I did one of them about. Here's the other.
R = V / It
R = 6 / 6
R = 1 ohm just what you got before.
====================
Power
P = V * I
P1 = 6 * 2 = 12 watts
P2 = 6*1 = 6 watts
P3 = 6*3 = 18 watts
Pt = 36 watts.
Pt can be done by using the voltage * the total current
Pt = 6 volts * 6 amps = 36 watts, just what you would expect.
