All categories

2 years ago

A type of adjustable square that can be used to set, test, and transfer angles is called a

Engineering

1 answer:

bekas [8.4K]2 years ago

5 0

Answer:

pocket cut

Explanation:

type of adjustable square that can be used to set test and transfer angles. sliding t bevel.

You might be interested in

Water at a pressure of 3 bars enters a short horizontal convergent channel at 3.5 m/s. The upstream and downstream diameters of

earnstyle [38]

Answer:

The pressure reduces to 2.588 bars.

Explanation:

According to Bernoulli's theorem for ideal flow we have

$\frac{P}{\gamma _{w}}+\frac{V^{2}}{2g}+z=constant$

Since the losses are neglected thus applying this theorm between upper and lower porion we have

$\frac{P_{u}}{\gamma _{w}}+\frac{V-{u}^{2}}{2g}+z_{u}=\frac{P_{L}}{\gamma _{w}}+\frac{V{L}^{2}}{2g}+z_{L}$

Now by continuity equation we have

$A_{u}v_{u}=A_{L}v_{L}\\\\\therefore v_{L}=\frac{A_{u}}{A_{L}}\times v_{u}\\\\v_{L}=\frac{d^{2}_{u}}{d^{2}_{L}}\times v_{u}\\\\\therefore v_{L}=\frac{2500}{900}\times 3.5\\\\\therefore v_{L}=9.72m/s$

Applying the values in the Bernoulli's equation we get

$\frac{P_{L}}{\gamma _{w}}=\frac{300000}{\gamma _{w}}+\frac{3.5^{2}}{2g}-\frac{9.72^{2}}{2g}(\because z_{L}=z_{u})\\\\\frac{P_{L}}{\gamma _{w}}=26.38m\\\\\therefore P_{L}=258885.8Pa\\\\\therefore P_{L}=2.588bars$

6 0

3 years ago

Three tool materials (high-speed steel, cemented carbide, and ceramic) are to be compared for the same turning operation on a ba

Tpy6a [65]

Answer:

Among all three tools, the ceramic tool is taking the least time for the production of a batch, however, machining from the HSS tool is taking the highest time.

Explanation:

The optimum cutting speed for the minimum cost

$V_{opt}= \frac{C}{\left[\left(T_c+\frac{C_e}{C_m}\right)\left(\frac{1}{n}-1\right)\right]^n}\;\cdots(i)$

Where,

C,n = Taylor equation parameters

$T_h$ =Tool changing time in minutes

$C_e$ =Cost per grinding per edge

$C_m$ = Machine and operator cost per minute

On comparing with the Taylor equation $VT^n=C$ ,

Tool life,

$T= \left[ \left(T_t+\frac{C_e}{C_m}\right)\left(\frac{1}{n}-1\right)\right]}\;\cdots(ii)$

Given that,

Cost of operator and machine time $=\$40/hr=\$0.667/min$

Batch setting time = 2 hr

Part handling time: $T_h=2.5$ min

Part diameter: $D=73 mm$ $=73\times 10^{-3} m$

Part length: $l=250 mm=250\times 10^{-3} m$

Feed: $f=0.30 mm/rev= 0.3\times 10^{-3} m/rev$

Depth of cut: $d=3.5 mm$

For the HSS tool:

Tool cost is $20 and it can be ground and reground 15 times and the grinding= $2/grind.

So, $C_e=$ $\$20/15+2=\$3.33/edge$

Tool changing time, $T_t=3$ min.

$C= 80 m/min$

$n=0.130$

(a) From equation (i), cutting speed for the minimum cost:

$V_{opt}= \frac {80}{\left[ \left(3+\frac{3.33}{0.667}\right)\left(\frac{1}{0.13}-1\right)\right]^{0.13}}$

$\Rightarrow 47.7$ m/min

(b) From equation (ii), the tool life,

$T=\left(3+\frac{3.33}{0.667}\right)\left(\frac{1}{0.13}-1\right)\right]}$

$\Rightarrow T=53.4$ min

(c) Cycle time: $T_c=T_h+T_m+\frac{T_t}{n_p}$

where,

$T_m=$ Machining time for one part

$n_p=$ Number of pieces cut in one tool life

$T_m= \frac{l}{fN}$ min, where $N=\frac{V_{opt}}{\pi D}$ is the rpm of the spindle.

$\Rightarrow T_m= \frac{\pi D l}{fV_{opt}}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 47.7}=4.01 min/pc$

So, the number of parts produced in one tool life

$n_p=\frac {T}{T_m}$

$\Rightarrow n_p=\frac {53.4}{4.01}=13.3$

Round it to the lower integer

$\Rightarrow n_p=13$

So, the cycle time

$T_c=2.5+4.01+\frac{3}{13}=6.74$ min/pc

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times6.74+\frac{3.33}{13}=\$4.75/pc$

(e) Total time to complete the batch= Sum of setup time and production time for one batch

$=2\times60+ {50\times 6.74}{50}=457 min=7.62 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times4.01}{457}=0.4387=43.87\%$

Now, for the cemented carbide tool:

Cost per edge,

$C_e=$ $\$8/6=\$1.33/edge$

Tool changing time, $T_t=1min$

$C= 650 m/min$

$n=0.30$

(a) Cutting speed for the minimum cost:

$V_{opt}= \frac {650}{\left[ \left(1+\frac{1.33}{0.667}\right)\left(\frac{1}{0.3}-1\right)\right]^{0.3}}=363m/min$ [from(i)]

(b) Tool life,

$T=\left[ \left(1+\frac{1.33}{0.667}\right)\left(\frac{1}{0.3}-1\right)\right]=7min$ [from(ii)]

(c) Cycle time:

$T_c=T_h+T_m+\frac{T_t}{n_p}$

$T_m= \frac{\pi D l}{fV_{opt}}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 363}=0.53min/pc$

$n_p=\frac {7}{0.53}=13.2$

$\Rightarrow n_p=13$ [ nearest lower integer]

So, the cycle time

$T_c=2.5+0.53+\frac{1}{13}=3.11 min/pc$

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times3.11+\frac{1.33}{13}=\$2.18/pc$

(e) Total time to complete the batch $=2\times60+ {50\times 3.11}{50}=275.5 min=4.59 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times0.53}{275.5}=0.0962=9.62\%$

Similarly, for the ceramic tool:

$C_e=$ $\$10/6=\$1.67/edge$

$T_t-1min$

$C= 3500 m/min$

$n=0.6$

(a) Cutting speed:

$V_{opt}= \frac {3500}{\left[ \left(1+\frac{1.67}{0.667}\right)\left(\frac{1}{0.6}-1\right)\right]^{0.6}}$

$\Rightarrow V_{opt}=2105 m/min$

(b) Tool life,

$T=\left[ \left(1+\frac{1.67}{0.667}\right)\left(\frac{1}{0.6}-1\right)\right]=2.33 min$

(c) Cycle time:

$T_c=T_h+T_m+\frac{T_t}{n_p}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 2105}=0.091 min/pc$

$n_p=\frac {2.33}{0.091}=25.6$

$\Rightarrow n_p=25 pc/tool\; life$

So,

$T_c=2.5+0.091+\frac{1}{25}=2.63 min/pc$

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times2.63+\frac{1.67}{25}=$1.82/pc$

(e) Total time to complete the batch

$=2\times60+ {50\times 2.63}=251.5 min=4.19 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times0.091}{251.5}=0.0181=1.81\%$

3 0

4 years ago

The best saw for cutting miter joints is the

ZanzabumX [31]

Answer:

The best saw for cutting miter joints is the backsaw.

Add-on:

i hope this helped at all.

6 0

3 years ago

For a turning operation, you have selected a high-speed steel (HSS) tool and turning a hot rolled free machining steel. Your dep

Alisiya [41]

Answer:

MRR = 1.984

Explanation:

Given that

Depth of cut ,d=0.105 in

Diameter D= 1 in

Speed V= 105 sfpm

feed f= 0.015 ipr

Now the metal removal rate given as

MRR= 12 f V d

d= depth of cut

V= Speed

f=Feed

MRR= Metal removal rate

By putting the values

MRR= 12 f V d

MRR = 12 x 0.015 x 105 x 0.105

MRR = 1.984

Therefore answer is -

1.944

8 0

3 years ago

Prepare deflection angles for staking the curves in problem 2-2. In every example assume that Sta. P.I. = 37+53.21. Carry the re

weeeeeb [17]

Answer:

ya mom

Explanation:

4 0

3 years ago