All categories

3 years ago

Complete the following sentence.

Engineering

1 answer:

Rom4ik [11]3 years ago

6 0

Answer:

improved

Explanation:

You might be interested in

Explain how a CO2 cartridge powers the dragster you will be building. A good website to use is How Stuff Works. (howstuffworks.c

andrezito [222]

Answer

C02 cartridges are compressed.

Explanation:

The C02 Cartridge will be used to power our dragsters by the compression inside of the bottle. Since C02 is a compressed gas inside of a small container, The pressure when released my provide enough force to move the dragster at high speeds. An example of this would be like an air soft gun. some air soft guns are used by small C02 Cartridges, which let out a strong burst of compressed C02, which fires the projectiles at very high speeds.

5 0

3 years ago

Read 2 more answers

An incompressible fluid flows between two infinite stationary parallel plates. The velocity profile is given by u=umaxðAy2 + By+

nexus9112 [7]

Answer:

the volume flow rate per unit depth is:

$\frac{Q}{b} = \frac{2}{3} u_{max} h$

the ratio is : $\frac{V}{u_{max}}=\frac{2}{3}$

Explanation:

From the question; the equations of the velocities profile in the system are:

$u = u_{max}(Ay^2+By+C)$ ----- equation (1)

The above boundary condition can now be written as :

At y= 0; u =0 ----- (a)

At y = h; u =0 -----(b)

At y = $\frac{h}{2}$ ; u = $u_{max}$ ------(c)

where ;

A,B and C are constant

h = distance between two plates

u = velocity

$u_{max}$ = maximum velocity

y = measured distance upward from the lower plate

Replacing the boundary condition in (a) into equation (1) ; we have:

$u = u_{max}(Ay^2+By+C) \\ \\ 0 = u_{max}(A*0+B*0+C) \\ \\ 0=u_{max}C \\ \\ C= 0$

Replacing the boundary condition (b) in equation (1); we have:

$u = u_{max}(Ay^2+By+C) \\ \\ 0 = u_{max}(A*h^2+B*h+C) \\ \\ 0 = Ah^2 +Bh + C \\ \\ 0 = Ah^2 +Bh + 0 \\ \\ Bh = - Ah^2 \\ \\ B = - Ah \ \ \ \ \ --- (d)$

Replacing the boundary condition (c) in equation (1); we have:

$u = u_{max}(Ay^2+By+C) \\ \\ u_{max}= u_{max}(A*(\frac{h^2}{2})+B*\frac{h}{2}+C) \\ \\ 1 = \frac{Ah^2}{4} +B \frac{h}{2} + 0 \\ \\ 1 = \frac{Ah^2}{4} + \frac{h}{2}(-Ah) \\ \\ 1= \frac{Ah^2}{4} - \frac{Ah^2}{2} \\ \\ 1 = \frac{Ah^2 - Ah^2}{4} \\ \\ A = -\frac{4}{h^2}$

replacing $A = -\frac{4}{h^2}$ for A in (d); we get:

$B = - ( -\frac{4}{h^2})h$ $B = \frac{4}{h}$

replacing the values of A, B and C into the velocity profile expression; we have:

$u = u_{max}(Ay^2+By+C) \\ \\ u = u_{max} (-\frac{4}{h^2}y^2+\frac{4}{h}y)$

To determine the volume flow rate; we have:

$Q = AV \\ \\ Q= \int\limits^h_0 (u.bdy)$

Replacing $u_{max} (-\frac{4}{h^2}y^2+\frac{4}{h}y) \ for \ u$

$\frac{Q}{b} = \int\limits^h_0 u_{max}(-\frac{4}{h^2} y^2+\frac{4}{h}y)dy \\ \\ \frac{Q}{b} = u_{max} \int\limits^h_0 (-\frac{4}{h^2} y^2+\frac{4}{h}y)dy \\ \\ \frac{Q}{b} = u_{max} (-\frac{-4}{h^2}\frac{y^3}{3} +\frac{4}{h}\frac{y^2}{y})^ ^ h}}__0 }} \\ \\ \frac{Q}{b} =u_{max} (-\frac{-4}{h^2}\frac{h^3}{3} +\frac{4}{h}\frac{h^2}{y})^ ^ h}}__0 }} \\ \\ \frac{Q}{b} = u_{max}(\frac{-4h}{3}+\frac{4h}2} ) \\ \\ \frac{Q}{b} = u_{max}(\frac{-8h+12h}{6}) \\ \\ \frac{Q}{b} =u_{max}(\frac{4h}{6})$

$\frac{Q}{b} = u_{max}(\frac{2h}{3}) \\ \\ \frac{Q}{b} = \frac{2}{3} u_{max} h$

Thus; the volume flow rate per unit depth is:

$\frac{Q}{b} = \frac{2}{3} u_{max} h$

Consider the discharge ;

Q = VA

where :

A = bh

Q = Vbh

$\frac{Q}{b}= Vh$

Also; $\frac{Q}{b} = \frac{2}{3} u_{max} h$

Then;

$\frac{2}{3} u_{max} h = Vh \\ \\ \frac{V}{u_{max}}=\frac{2}{3}$

Thus; the ratio is : $\frac{V}{u_{max}}=\frac{2}{3}$

5 0

4 years ago

Isormophous phase diagram

shusha [124]

Answer:

Phase diagrams represent the relationship between temperature and the composition of phases present at equilibrium. An isomorphous system is one in which the solid has the same structure for all compositions. The phase diagram shown is the diagram for Cu-Ni, which is an isomorphous alloy system.

Hope it help you friend