1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
spin [16.1K]
3 years ago
10

Describe two characteristics that bridges and skyscrapers have in common.

Engineering
1 answer:
Elan Coil [88]3 years ago
7 0

Answer:

skyscrapers and bridges both have structural builds accounting for the influence of wind and they both cost big money

Explanation:

You might be interested in
PLEASE HELP QUICK!!
ivolga24 [154]

R01= 14.1 Ω

R02=  0.03525Ω

<h3>Calculations and Parameters</h3>

Given:

K= E2/E1 = 120/2400

= 0.5

R1= 0.1 Ω, X1= 0.22Ω

R2= 0.035Ω, X2= 0.012Ω

The equivalence resistance as referred to both primary and secondary,

R01= R1 + R2

= R1 + R2/K2

= 0.1 + (0.035/9(0.05)^2)

= 14.1 Ω

R02= R2 + R1

=R2 + K^2.R1

= 0.035 + (0.05)^2 * 0.1

= 0.03525Ω

Read more about resistance here:

brainly.com/question/17563681

#SPJ1

5 0
2 years ago
The intake and exhaust processes are not considered in the p-V diagram of Otto cycle. a) true b) false
vovangra [49]

Answer:

b) false

Explanation:

We know that Otto cycle is the ideal cycle for all petrol working engine.In Otto cycle all process are consider is ideal ,means there is no any ir-reversibility in the processes.

It consist four processes

1-2:Reversible adiabatic compression

2-3:Constant volume heat addition

3-4:Reversible adiabatic expansion

3-4:Constant volume heat rejection

Along with above 4 processes intake and exhaust processes are parallel to each other.From the P-v diagram we can see that all processes.

But actually in general we are not showing intake and exhaust line then it did not mean that in Otto cycle did not have intake and exhaust processes.

6 0
3 years ago
Explain three (3) modes of heat transfer in air conditioning system.
LenKa [72]

Answer:

1. Conduction

2. Convection

3. Radiation

Explanation:

The 3 modes of heat transfer i an air conditioning system:

1. Conduction:

The transfer of heat by conduction  takes place in solid and is when the conduction takes place as a result of direct contact in between the interacting material which transfer the heat energy from particle to particle thus conducting the heat through out the system.

2. Convection:

The other mode for the transfer of heat which takes place especially in fluids - gases and liquids is through the technique of convection in which the transfer of heat takes place by the circular motion of the atoms and molecules of the fluid which carries the heat energy and results in the distribution of the heated fluid in the entire system thus transferring all the heat energy in the entire system.

3. Radiation:

The third mode of heat transfer in the air conditioning system is through radiation. This method transfers the heat by making use of the electro-magnetic radiation in the infra red spectrum where the waves of the spectrum transfers the heat energy with the help of a medium or without any medium at all.

Thus making the radiation method of heat transfer as the only method out of the three methods which does not require the material medium for the transfer of heat energy.

4 0
3 years ago
List and explain 4 factors you need to observe while stick welding to make a good “consistent” bead
ch4aika [34]

Answer:I don’t know this one

Explanation:

5 0
3 years ago
How many hours should it take an articulated wheel loader equipped with a 4-yd^3 bucket to load 3000 yd^3 of gravel (average mat
densk [106]

Answer:

17 hours 15 minutes

Explanation:

See attached picture.

4 0
3 years ago
Other questions:
  • g Consider a thin opaque, horizontal plate with an electrical heater on its backside. The front end is exposed to ambient air th
    11·1 answer
  • For the pipe-fl ow-reducing section of Fig. P3.54, D 1 5 8 cm, D 2 5 5 cm, and p 2 5 1 atm. All fl uids are at 20 8 C. If V 1 5
    10·1 answer
  • n open feedwater heater operates at steady state with liquid water entering inlet 1 at 10 bar, 50°C. A separate stream of steam
    8·1 answer
  • Air at 7 deg Celcius enters a turbojet engine at a rate of 16 kg/s and at a velocity of 300 m/s (relative to engine). Air is hea
    7·1 answer
  • Which one of the following activities is not exempt from licensure pursuant to Chapter 471, F.S.? A person practicing engineerin
    5·1 answer
  • A 0.9% solution of NaCl is considered isotonic to mammalian cells. what molar concentration is this?
    10·1 answer
  • 5) /
    12·1 answer
  • How is air pressure affected by the shape of an aircraft wing
    14·1 answer
  • What Number Am I?
    13·1 answer
  • 9
    15·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!